There are 2 basic designs for struts and shockers, twin tube and monotube, the following video's explain and demonstrate how each design functions.
https://www.youtube.com/watch?v=hzC_TOHGQnE
https://www.youtube.com/watch?v=2LVYWW...
500 results in 1.0328 seconds.
-
I use a 21mm single hex deep impact socket, 1/2" drive.
Plenty to choose from , but here is a sample.
https://www.australianonlinecarparts...eep-impact-skt
OJ.Leave a comment:
-
I have only seen a 25mm/30mm spacer fitted to the top of the airbags to protect the airbag from the bolt end of the bolt that attaches the subframe assembly to the body. On the 2x Gen 4's I have worked on with airbags both had lifted suspension, 1 had...Leave a comment:
-
The plastic wrap on the top of the original coils is also an attempt by Mitsubishi to reduce suspension noise transfer to the cabin.
When you tightened up the top mounts of the rear shockers are you 100% sure the shocker pin and bushes were...Leave a comment:
-
Hi Serapax,
X-Rox bars offer little real protection, particular on the sides, but the centre protection is better than no protection at all.
It really depends on the reasons for fitting a bar and this determines the choice of bar....Leave a comment:
-
Hi Stu,
Yes, a load index of 120 will be a 10ply rated Light Truck construction tyres, so these will ride firmer and use more fuel even if they have a tread pattern that is not aggressive. If the tread pattern is aggressive then you can...Leave a comment:
-
Airbags in coil springs act by expanding outwards and not lengthwise.
It is the outwards expansion of the airbag between the coil winds that provide the additional increase in effective spring rate to cope with higher suspension loads.
h...Leave a comment:
-
Hi Stu,
Your rims will be 7"x16" and the tyre placard would mostly likely indicate that 265/70R16 is the factory tyre size.
On a 7"rim you can fit the following tyre sizes;
1. 265/70R16 - standard diameter....Leave a comment:
-
As a coil spring compresses the end of the wire rotates, so standard practice when fitting coils is leaving a 10-12mm gap, so the coil can rotate freely as it compresses, and it is this rotation that wears out the lower coil insulators on the Gen 3/4...Leave a comment:
-
Hi Ray,
Partsouq is the best online part number finder, just put your VIN in and it will access you to the parts diagrams for your Challenger.
https://partsouq.com/catalog/genuine...ogle&utm_campa...Leave a comment:
-
Hi Stu,
Load index is the maximum load a tyre is rated to carry at the maximum cold inflation pressure that is stated on the sidewall of the tyre.
In general a tyre that has a higher load index will be a stronger, stiffer and heavier...Leave a comment:
-
Has the noise only started after this work was carried out?
Tyres, have you checked wheel nut tensions with the weight of the wheels?
When the airbags were fitted, were the coils removed?
If so,
1. What was the condition...Leave a comment:
-
Because I have found multiple loose hub nuts, I now check them whenever I am doing suspension, driveline or brake work on Gen 4's.
36mm socket and 4mm x 40mm long split pins are required, vehicle weight must be off the wheels when checking the...Leave a comment:
-
Have you checked the wheel bearing hub nuts are tight?
Have you checked it is not the rear door rub blocks out of adjustment?
Has any work been recently done on the vehicle? If so what?
OJ.Leave a comment:
-
Hi Turbopsi,
Well done on the installation.
Your front ride heights are what I would have expected with the KCFR-34 coils.
The rear ride heights from the KCRS-35 are about 15mm to 20mm higher that I would have expected...Leave a comment:
-
Reply to Kings + OzTec SuspensionThere are 2 basic designs for struts and shockers, twin tube and monotube, the following video's explain and demonstrate how each design functions.
https://www.youtube.com/watch?v=hzC_TOHGQnE
https://www.youtube.com/watch?v=2LVYWW...1 day ago -
I use a 21mm single hex deep impact socket, 1/2" drive.
Plenty to choose from , but here is a sample.
https://www.australianonlinecarparts...eep-impact-skt
OJ.1 day ago -
I have only seen a 25mm/30mm spacer fitted to the top of the airbags to protect the airbag from the bolt end of the bolt that attaches the subframe assembly to the body. On the 2x Gen 4's I have worked on with airbags both had lifted suspension, 1 had...1 day ago
-
Reply to 2013 NW GLX - Rear knockThe plastic wrap on the top of the original coils is also an attempt by Mitsubishi to reduce suspension noise transfer to the cabin.
When you tightened up the top mounts of the rear shockers are you 100% sure the shocker pin and bushes were...2 days ago -
Hi Serapax,
X-Rox bars offer little real protection, particular on the sides, but the centre protection is better than no protection at all.
It really depends on the reasons for fitting a bar and this determines the choice of bar....2 days ago -
Hi Stu,
Yes, a load index of 120 will be a 10ply rated Light Truck construction tyres, so these will ride firmer and use more fuel even if they have a tread pattern that is not aggressive. If the tread pattern is aggressive then you can...2 days ago -
Airbags in coil springs act by expanding outwards and not lengthwise.
It is the outwards expansion of the airbag between the coil winds that provide the additional increase in effective spring rate to cope with higher suspension loads.
h...2 days ago -
Hi Stu,
Your rims will be 7"x16" and the tyre placard would mostly likely indicate that 265/70R16 is the factory tyre size.
On a 7"rim you can fit the following tyre sizes;
1. 265/70R16 - standard diameter....2 days ago -
Reply to 2013 NW GLX - Rear knockAs a coil spring compresses the end of the wire rotates, so standard practice when fitting coils is leaving a 10-12mm gap, so the coil can rotate freely as it compresses, and it is this rotation that wears out the lower coil insulators on the Gen 3/4...2 days ago
-
Hi Ray,
Partsouq is the best online part number finder, just put your VIN in and it will access you to the parts diagrams for your Challenger.
https://partsouq.com/catalog/genuine...ogle&utm_campa...3 days ago -
Hi Stu,
Load index is the maximum load a tyre is rated to carry at the maximum cold inflation pressure that is stated on the sidewall of the tyre.
In general a tyre that has a higher load index will be a stronger, stiffer and heavier...3 days ago -
Reply to 2013 NW GLX - Rear knockHas the noise only started after this work was carried out?
Tyres, have you checked wheel nut tensions with the weight of the wheels?
When the airbags were fitted, were the coils removed?
If so,
1. What was the condition...3 days ago -
Reply to Fulcrum Formula Suspension kitBecause I have found multiple loose hub nuts, I now check them whenever I am doing suspension, driveline or brake work on Gen 4's.
36mm socket and 4mm x 40mm long split pins are required, vehicle weight must be off the wheels when checking the...3 days ago -
Reply to 2013 NW GLX - Rear knockHave you checked the wheel bearing hub nuts are tight?
Have you checked it is not the rear door rub blocks out of adjustment?
Has any work been recently done on the vehicle? If so what?
OJ.3 days ago -
Reply to Fulcrum Formula Suspension kitHi Turbopsi,
Well done on the installation.
Your front ride heights are what I would have expected with the KCFR-34 coils.
The rear ride heights from the KCRS-35 are about 15mm to 20mm higher that I would have expected...3 days ago -
Reply to Crankshaft Woodruff KeyMoneypit's profile list a 1990 Pajero with 4D56 engine., and the photo posted does show the timing belt with a balance belt behind.
So looking at Partsouq online, the Part Number is MD000606 which is a 5x9.6 Woodroof key.
Moneypit, if you...3 days ago -
Reply to Newbie to 4wd communityHi and welcome Ray, the PB/PC Challenger sub-forum has plenty of info and there is no shortage of assistance from forum members when required, this is also the best place to read up about your Challenger and to ask any questions. With 2800 threads and...4 days ago
-
Reply to Manual Vs Auto for NT onwardNW Manual dual mass flywheel?
https://partsouq.com/en/catalog/genu...7ZHZxcGl1KCZUc...6 days ago -
Reply to 2022 qf gsrHi Joh,
1. I agree leg room is restricted and footwell is shallow for those over 6ft, 100+kg and have large feet, but the PS is not a full size 4wd.
2. Why not change the interior light globes to LED?
3. Seats 6 and 7 are removable,...6 days ago -
Reply to Ideal antenna length / dBiI used to swap between a 6db long range and a short 2db flexible for off road, I gave up on this and now I use a 4db flexible that is a good allrounder compromise.
You are better off having a 4db on the roof rack than a 6db on the bullbar.
...1 week ago -
Reply to My first ever 4x4!Hi Matt,
Putting the Chassis Number into Partsouq, indicate the Pajero was built 08/1992 and is a model V43 NH GLX with a 3 litre V6, 5 speed manual with Super Select.
https://partsouq.com/en/catalog/genu...?c=Mitsubishi&...1 week ago -
Reply to Manual Vs Auto for NT onwardAuto's are much better suited to modern CRD engines that produce a lot of power and torque, try doing a hill start when off road or when towing with a manual gear box and a CRD engine, and you will soon learn you really need to slip the clutch a lot,...1 week ago
-
A quick goggle search found these threads.
https://www.pajeroforum.com.au/forum...oor-won-t-open
https://www.pajeroforum.com.au/forum...eeded-rear-doo...1 week ago -
-
Roof racks and trays can weigh from 15kg to 45kg and this weigh must be taken into consideration as it is included in the roof payload.
First up list and weigh all the items you want to carry on the roof and that will indicated what size rack you...1 week ago -
Reply to Factory fitted tyres -QF Models.275/65R18 tyres are 815mm in theoretical diameter so this is 40mm larger in theoretical diameter than the factory tyre size of 265/60R18 which is 775mm in diameter but the AT811 are 823mm in actual diameter so 47mm over diameter, this is in theory are...1 week ago
-
Missing a digit or very light steering, Redbruce?
OJ....1 week ago -
Hi Dreamimg,
The thick rubber pad under the top mount is normal.
580mm front EBH is way too high, and illegal, I am surprised you are not getting unwanted activations of ABS, TC and ASC systems, 540mm to 545mm is s more sensible, safe...2 weeks ago -
Reply to Weird Whistling SoundHave you checked that the multi-rib belt is in all the correct pulley grooves and there is not some misalignment of the belt that is putting a side load on the belt?
Are all the grooved pulleys clean to their full depth?
OJ.2 weeks ago -
Hi Brendan,
Are the rims, 7"or 7.5" wide?
Mitsubishi factory alloys are generally made by Enkei, if so these are very strong and high quality.
No legal or mechanical issues with running 245/65R17 size tyres as long...2 weeks ago -
You are not the first person to have an issue with a plug & play EGR delete cable, I have not tested a unit to confirm the wiring design, but I suspect it leaves the thermistor that is in the mass airflow sensor still in the control circuit.
...2 weeks ago -
Reply to 2011 PB airbag light just came onCall BS on this!
This forum thread has over 450 posts including actions take by MMAL to fix this very common problem at no cost.
https://www.pajeroforum.com.au/forum...30-srs-airbag-...2 weeks ago -
Reply to Torque converter lock upI would think that there are enough of the MM4x4 Lockup kits being used for many years and 10's of thousand kms that if there was a issue then these would have come to light by now.
OJ....2 weeks ago -
Reply to Torque converter lock upWhat you are seeing is the normal behaviour of the factory AT program and unfortunately it cannot be adjusted by any MMAL technician.
The MY18 NX has a higher diff ratios than the earlier NX, NW, NT, etc but still have the same gearbox ratios,...2 weeks ago -
Reply to Shift ClunkThat is your problem.
The Pajero Sport (Pajero and Challenger) have drum in-disc park brake, so when the park brake is applied and the vehicle is on an incline the vehicle will move slightly downhill after the park brake is applied as the backlash...2 weeks ago -
Once you have the weights and your ride heights, post these and we can look at what spring options are available.
I would always go for progressive rate coils where possible as these increase the spring rate under deep compression.
Both King...2 weeks ago -
You have a single axle caravan so having the drawbar level when hitched up is not as important as if the caravan/trailer had dual axles.
If it was a dual axle caravan/trailer I would be suggesting you level the drawbar and then measure the height...2 weeks ago -
Reply to Shift ClunkHi Leon,
Are you placing the transmission in N with you foot on the brake, applying the park brake, releasing the foot brake so the park brake takes up the load and then putting the transmission in P?
OJ.2 weeks ago -
Hi Hartski,
There is no point in getting a lift unless you need one for off road driving, your NT will have 200,000+Kms on the driveline and if you raise the normal ride height up too much then you can get harmonics and vibrations because...2 weeks ago -
Reply to Can't press transfer case lever downWell done for sorting it out and also for reporting back to the forum.
OJ....2 weeks ago -
Hi Donny,
530mm front ride height is a good ride height if you tow and have towball loads of over 150kg. 545mm or 550mm front ride height is too high if you tow and have 150kg+ towball loads because when the towball loads are applied there is weight...2 weeks ago -
Hi Donny,
40mm to 45mm lift is about the maximum legal lift above factory heights, because yo must retain at least 2/3’s of the factory droop travel. Suspension kits are marketed as 50mm:2 inch lifts because the suppliers rely on the factory...2 weeks ago -
Reply to One for the mathematicians ...All that is missing from this thread is a campfire and a glass or 2 of red wine!
From a practical application point of view, and what 99.9999999999% of the population are taught and use on a daily basis then, any number multiplied by zero...3 weeks ago -
265/60R18 is the stock standard factory tyre size and is 775mm in diameter, so a 265/65R18 is 801.5mm in diameter 26.5mm larger in diameter and is a legal fitment, It is a common upsize tyre used by many Pajero owners, if the tyre is an aggressive LT...3 weeks ago
-
Reply to Can't press transfer case lever downHi Andy,
I suggest you put your VIN in to Partsouq and then look at the parts diagrams of the transfer case high to low shift mechanism. It appears the push down function at the start of the shift movement is to unlock the transfer lever...3 weeks ago -
Reply to Can't press transfer case lever down3 weeks ago
-
Reply to Can't press transfer case lever downAre you pressing down first, then pushing the lever to the left then forwards?
OJ.3 weeks ago -
Reply to Can't press transfer case lever downGen 2 transfer case is manual/mechanical operation.
Is the main gearbox in neutral?
Have you tried with the engine not running?
OJ.3 weeks ago -
Reply to Front door speakers cutting out3 weeks ago
-
Reply to Koni 90 Front StrutsYes. Yes and Yes.
This is the strut bump stop that protects the strut in deep compression.
OJ.3 weeks ago -
Reply to Rear coil spacersHi Homer,
I understand your situation and can sense your frustration with the problems you are having both with the Pajero suspension and personally.
Hopefully we can hep you out with sorting your suspension out and this will...3 weeks ago -
Reply to Rear coil spacersNo problems with the reply Homer.
So is the spacer thickness 50mm or is a 25/30mm thick spacer that provides a 50mm increase in ride height?
OJ....3 weeks ago -
Reply to Rear coil spacersI doubt if a 50mm thick spacer will keep the top of the coil located correctly and a 50mm thick spacer will increase the ride height by around 100mm!
Gen 4 Rear factory ride height is 533/5mm and legally you can only increase the ride height by...3 weeks ago -
It is all about the prevention of glare and discomfort to oncoming traffic, so misaligned headlights, crazed/opaque/dirty head light lenses and or headlight covers that alter the headlight beam pattern and cause glare render the vehicle unroadworthy...4 weeks ago
-
Hi Redbruce,
Highest halogen colour temperature I have seen is between 3600K and 3900K, but these are Performance Plus series globes, the trade off is they are more expensive and have a much shorter life.
My 20"single row Lightforce...4 weeks ago -
Reply to Aftermarket suspensionAny driveline that has been operating at certain angles for an extended period of time, has the potential to become noisy and generate vibrations if the operating angle is changed.
OJ....4 weeks ago -
Reply to Why not to use a WDHI am with Mundy 55, I am of the opinion that a correctly setup and used WDH as more advantages than disadvantages, especially in regards to safety.
A correctly sized and setup WDH is only meant to transfer the weight that was transferred off the...4 weeks ago -
-
Reply to Aftermarket suspensionWelcome to the forum.
Lifting the ride height of a 17 year old Gen 3 Pajero with 300,000+kms on the odometer is a potential money pit that once you start down the path it will cost you to go forwards or backwards.
Problems...4 weeks ago -
No problem Sean, best things you can do to increase the reliability and longevity of tyres is to;
1. Reduce tyre pressures when off the bitumen, knowing your axle loads enables you to use load inflation tables to determine the minimum tyre pressure...4 weeks ago -
Hi Sean,
Most trailer hubs require rims that have a larger centre bore diameter than the Pajero Sport/Challenger/Triton and Gen 3/4 Pajero which have a 67.1mm bore, this means even if the offset difference is tolerable, the trailer wheel...4 weeks ago -
No response from Kings, but I did not follow it up either.
If Kings could well have been like many other manufacturing businesses in Australia, that are suffering from the affects staff absenteeism due to COVID restrictions and illness over...4 weeks ago -
No side gussets so ram air will take the path of least resistance and not go through the intercooler.
Expanded aluminium mesh will fatigue and crack on corrugated roads, and will not stop a stick big that is big enough to spear the intercooler....4 weeks ago -
Reply to PB Challenger OverheatingGreat to know that MMAL are still supporting the PB/PC Challengers and MN Tritons have have confirmed coolant consumption problems.
OJ....4 weeks ago -
Reply to Will I need bash plates?I have done 4 Simpson crossings, and have never had an issue with spinifex build up. If you stay on the well used tracks then I do not believe it is a major risk, just take sensible precautions.
OJ.22-04-22, 10:22 PM -
Reply to Will I need bash plates?Last trip across the Simpson in 2017, I travelled with Njswb (Auto NT) and Pajero 12 (Auto NW), Oodnadatta to Birdsville via Dalhousie, French, Colsen, WAA, Knolls, Rig, K1 and QAA , 750km each vehicle was at GVM + 100kg to 200kg, each vehicle used between...22-04-22, 12:03 AM
-
Reply to Will I need bash plates?Hi Aspiro,
Weight is your enemy, so anything you can do to reduce weight is beneficial.
You have the biggest risks covered for a desert crossing with intercooler, sump and rear bumper.
You will need to have 130 litres of an auto...21-04-22, 09:01 PM -
Reply to Qztec SuspensionHi Brisvegas,
The rear axle on the Challenger and Pajero Sport is a live axle trailing arm design so there are no wheel alignment adjusters or alignment to worry about.
However whilst the rear coils are out it is worth inspection the...20-04-22, 12:12 PM -
Page 6 & 7 of the User Manual, clearly explains the senisty adjustment and gives a warning of not to set it too low. Range is 60 to 160 and default is 100, so check what the current setting is and then pick a number to test. If it was me and the...19-04-22, 10:04 PM
-
The 07 NS has the Jatco 5 speed fitted so this is the same auto as the PB/PC Challenger so the functions of Auto Mate is slightly different than Auto Mate/Pro that is used on the NT onwards with the Aisin 5 speed auto.
Jemsquash, if you...19-04-22, 08:39 AM -
Reply to 2008 Pajero Transmission problemsHi Athino,
Thank you for answering all of our questions in detail.
Your auto transmission is a JATCO V5A5A, and these transmission can be sensitive to what ATF fluid is used, the conditions of the fluid and also the ATF level....18-04-22, 03:02 PM -
Reply to 2008 Pajero Transmission problemsAgree with Geopaj, we need to know if it is a Jatco or Aisin transmission.
The Jatco has a ATF dipstick and the Aisin does not have a dipstick.
Once we know what transmission is fitted then we help more.
You posted that the transmission...18-04-22, 11:33 AM -
Reply to 2011 PB airbag light just came onAirbag light can only be reset with a Scan tool.
You also need to know the fault code/s as there are multiple reasons why this light can come on.
Plenty of reading about this issue;
https://www.pajeroforum.com.au/forum/vehicles/cha...17-04-22, 10:23 PM -
Reply to Gear selector consolePart Number is 2420A043 and/or 2420A129, plenty available online.
https://www.ebay.com.au/itm/25525383...krid=705-13961...17-04-22, 06:19 PM -
Auto Mate, the PB Challenger would have been long gone if not from this mod.
My suspension set up, it suits my particular requirements nicely.
Lightbar, roof rack, storage system, EGR delete and highl ift tailgate struts are...15-04-22, 08:51 PM -
Reply to Options for anniversary tripThere are plenty of NSW National Parks close to Wollongong, like the Brindabella Ranges, Kosciuszko National Park, Snowy Mountains, Snowy Hydro, McKillops Bridge, etc, etc, plenty of history both natural and manmade if you are into museums, plenty of...15-04-22, 03:38 PM
-
Reply to Kaon Intercooler Bash PlateI consider the Kaon intercooler guard the best design as far as airflow is concerned based on the online photos but I have not seen one in real life, they tend to be more expensive especially when freight is added compared to Bushskinz and Boo's which...15-04-22, 09:45 AM
-
Yes but you would need to do a test fit to the front axle to double check the rim to caliper clearance.
OJ....14-04-22, 02:04 PM -
Reply to Too much ball weight?Looks like it has about 50mm of travel so what happens when you cross a spoon drain?
I could see this getting hung up and damaged really easily.
OJ.13-04-22, 12:41 PM -
Gen 3/4 Pajero rims have P46 offset and the Pajero Sport/Triton/Challenger have P38 offset so it is illegal to fit a P39 ot greater offset rim to a Pajero Sport as you ar narrowing the wheel track.
A P46 rim will not fit anyway.
O...12-04-22, 10:20 PM -
Hi Jacky,
Replacing struts and shockers does not raise the ride height of the vehicle, vehicle ride height is changed when the coils and or insulators are changed.
If you are happy with the factory ride height, handling and comfort...12-04-22, 10:15 PM -
Reply to I need soft suspension on NS SWBHi Fbo,
Original struts and shockers are undersized for off road and load carrying and struggle to control HD suspension.
KYB Excel are a OEM direct replacement.
I cannot see a physical problem with running Dobinson MT/IMS struts...11-04-22, 09:25 AM -
Reply to Suspension UpgradeHi Mick,
There are rubber insulators on the top of the rear coils only, Part Number MR491949 or MB844241 or 4140A567, they are readily available online for about $10 each.
Bottom of rear coils in metal to metal with the spring pad...09-04-22, 11:22 PM -
Hi and welcome to the forum Ed,
Since you have 30km of potholed roads to regularly traverse then I would be either selecting a stronger tyre than a P construction so either XL, 8ply/D LT or 10ply/E LT.
Since you will be heading...08-04-22, 01:05 PM -
Reply to Suspension UpgradeThe KCRS-23 and Aeon 5899 cones will firm up the rear nicely, retain sensible ride heights with rear axle weights up to about 250kg extra.
No need to change the front coils if you are happy with the ride height and spring rates, especially...07-04-22, 07:03 PM -
Reply to BatteryFor starting batteries I have been using Bosch S5 Silver Calcium, I am just about to change a 7 year old one in my Challenger and a 5 year old one in a NW, both batteries are struggling to start the engines after 4 or 5 days of not being started. The...07-04-22, 06:44 PM
-
Hi Brendan,
The standard Pajero Sport and Triton wheels have a P38 offset, this means the centreline of the tyre is 38mm offset inwards from the mating face of the wheel hub.
Legally you can change the offset that widen the vehicle...07-04-22, 06:07 PM -
Reply to nm pajeroHi Foss,
I can only help you if you clearly and accurately answer my questions.
Q1. Does the horn stop when Fuse 13 is removed?
Q2. Does the horn stop when Fuse 12 is removed?
OJ....06-04-22, 10:00 PM -
Reply to nm pajeroLooking at the Gen 3 circuit diagrams I have access to.
The horn will only function when the power from the coil of the relay is grounded via the horn switch, anti theft system, central locking system and key reminder system.
...06-04-22, 09:41 PM -
-
Reply to need to buy a body partFrom this link;
https://www.drive.com.au/caradvice/w...e-move-to-lhd/
"RHD cars aren’t an obscure rarity in the global market by any means, with over 60 countries currently using this format....06-04-22, 12:21 PM -
Reply to need to buy a body partFrom the photo you posted and then looking at the picture in Partsouq I would have thought it was the lefthand side and not the righthand. Is the wider flat section of the over fender flare rearwards or forwards of the wheel arch?
Also I cannot...05-04-22, 07:41 PM -
Reply to need to buy a body partJump onto Partsouq, enter your VIN and then search in the body section, for "overfender ff rh", they come pre-painted hence why the VIN is important and cost about AUD $90 +freight.
As an example of what you are looking for;...05-04-22, 02:41 PM -
Reply to Tyre SizeIncreasing the tyre size from 265/65R17 to 285/70R17 has more negatives than positives, when I look at it.
1. A 7% reduction in acceleration and braking performance.
2. 54mm diameter increase and the allowable limit is 50mm so RWC and insurance...05-04-22, 12:33 PM -
Hi Mark,
In regards to price, the Kaon plates are more complex in design and will take longer to manufacture so they will be more expensive. Freight prices have gone through the roof in the last 2 years and manufacturers cannot absorb this...05-04-22, 12:16 PM -
Reply to upgrade advise for 95 Pajero !!Hi Gemster,
Looking at the Service manual on Mitsubishi links, it appears the PB/PC Challengers rear suspension is almost identical to the Gen 2 rear suspension, the only difference I can find is the top mount of the rear shocker is a pin...05-04-22, 01:10 AM -
Reply to upgrade advise for 95 Pajero !!Hi Valiant,
Hard data on factory ride heights is non existent, overall height of the vehicle is between 1865mm and 1900 mm depending on the model, variations mainly due to the tyre size fitted.
Best guesstimate is about 510mm to 520mm...04-04-22, 09:01 PM -
Hi Mark,
Kaon do a transmission guard it is just not easy to find on their website.
https://www.kaon.com.au/transmission...i-pajero-gen-4
Problem with Bushskinz, Boo's Brown Davis and most other plates...04-04-22, 01:27 PM -
Hi Mark,
Bash plates if you are venturing off road, intercooler and engine sump most important even in sand, and the gearbox transfer plate if you are off road where there are large rocks and gutters of the tracks.
My opinion is the...04-04-22, 12:20 PM -
When I designed my custom drawer system it had the provision for 2x 42 litre Boab tanks fitted between the rear seat back and the forward side if the drawer system.
At around $250 each they are a much cheaper option than the alternative long range...31-03-22, 10:20 PM -
Reply to Pajero Sport Towing IssueHi Keith,
Although it appears your WDH is correctly transferring the front axle transferred weight off the rear axle and back to the front axle, the spring rate of the factory rear coils are still too low so not only will you get a greater...31-03-22, 09:27 PM -
Reply to Spare tyreYou need to make sure the foam does not absorb water, otherwise this may lead to corrosion of the wheel face.
I have a piece of flexible plastic sheet that is the same diameter as the rim, there is a slit in the centre of the plastic so the hub...31-03-22, 07:21 PM -
Reply to Pajero Sport Towing IssueHi Ian,
Even if the Pajero is sitting level you will still have unloaded the front axle by 107kg so depending on the front spring rates the front ride height could increase between 5mm and 15mm.
Are the front coils factory standard...31-03-22, 03:38 PM -
Reply to Pajero Sport Towing IssueHi Ian,
That makes more sense, 120kg off the front axle when hitched and no WDH connected and 100kg transferred back on to the front axle when the WDH is connected. This should result in the front hitched and WDH connected front ride height...31-03-22, 01:49 PM -
Reply to Pajero Sport Towing IssueHi Ian,
So if we assume the towball weight is 220kg, then when this is hitched up it will transfer 121kg off the front axle based on a 1.55 leverage ratio, so total rear axle weight is now 341kg. Then your connect the WDH 60kg is then transferred...31-03-22, 12:06 PM -
Reply to NT Pajero Issues - Help Please!Hi Lloyd,
I would be checking the fuel rail pressure sensor and the associated wiring and plugs as this is a common probable cause for both the fault codes you have reported.
Since the sensors seem not to have a history of failing,...31-03-22, 07:37 AM -
Reply to NT Pajero Issues - Help Please!Hi Lloyd,
From the online Service Manual;
Code No. P0093: Fuel Leak Problem
OPERATION
• Refer to Code No. P0192: Rail Pressure Sensor Circuit Low Input .
FUNCTION
• The...30-03-22, 09:59 PM -
Reply to Pajero Sport Towing IssueHi Ian,
What was your towball weight, before the WDH was connected?
OJ....30-03-22, 09:31 PM -
Hi Tom,
Remove the top off the airbox and remove the air cleaner, is there water in the base of the airbox?
Remove the hose between the throttle body and the intercooler outlet, is there water in the hose?
If the answer...30-03-22, 09:28 PM -
Reply to Pajero Sport Towing IssueHi Keith,
Dicko is correct you cannot ignore the rules of physics.
Apart form looking at your WDH setup/adjustment and upgrading the rear suspension I would suggest you brake leading into the corners before turning, this will...29-03-22, 09:16 PM -
Reply to NP diesel cooling systemI did agree with Geopaj about getting an exhaust gas in coolant test done as this will detect a small leak from the cooling system to the combustion chamber. Left unchecked, minor leaking can result in major problems. When the engine stops, the cooling...29-03-22, 05:03 PM
-
Reply to NP diesel cooling systemAgree with Geopaj, an exhaust gas in coolant presence test will establish if the head gasket is leaking.
For the coolant transfer back to the radiator to happen correctly, the radiator cap needs to be the correct part for the radiator, it...29-03-22, 12:55 PM -
Reply to Pajero Sport Towing IssueHi Keith,
I can see 2 possible reasons for your handling problems.
1. You may have too much pre load on your Anderson hitch, based on your statement that the Pajero Sport is sitting level. The amount of pre load applied should...29-03-22, 12:25 PM -
Reply to Roof weight concerns. Advice sought.Rear drawers and a fridge slide make living out of the vehicle much easier and more convenient.
My 2nd row seats are 60/40 split and weigh just over 60kg, the replacement storage boxes are about 20kg so I picked up 40kg of payload.
The boxes...29-03-22, 08:36 AM -
The unlocked slipping TC should not happen with Automate switched on.
OJ....28-03-22, 10:08 PM -
Reply to Fault code U1100Hi Grumps,
Before changing over the ATF cooler you could bypass the ATF cooler that is in the base of the radiator, from numerous reports this bypass can reduce ATF temps.
Your ATF can be too cold, the torque convertor will not lockup...28-03-22, 10:01 PM -
Reply to Roof weight concerns. Advice sought.Hi Bob,
The Gen 4 Pajero has a huge amount of room inside, more than enough room for 2 people doing extended touring, particularly if you remove the unused 2nd and 3rd row seats, this also reduces the weight significantly and gives you rear...28-03-22, 09:49 PM -
May 2018 Oodnadatta to Birdsville via French, Colson, WAA, Rig, French, K1 and QAA, 2x NW Pajero Autos and PB Challenger Auto, 750kms and 122 litres to 126litres across a 3x 4wds had TC lockups fitted, 16.5 lt/100kms so this is in line with what Kingbrown...28-03-22, 01:32 PM
-
The Frontier tanks are made from cross-linked polyethylene that is 7mm to 9mm thick so it is very strong and durable and about 1/2 the weight of a steel tank of similar size.
Most boating fuel tanks are now made from similar material as are the...27-03-22, 09:36 PM -
Reply to Rear wheel bearing and hub removalPenetrating spray like Inox or similar allow to soak, whilst waiting heat up the area with a electric heat gun (paint stripping type or even a hairdryer), more spray.
Make sure the lateral and toe control suspension arms are all connected to the...27-03-22, 02:20 PM -
Welcome Bob,
You do not say if you are vehicle only touring or towing, and if towing what weight and size.
Getting a factory 4wd setup for serious 4wd touring requires carefully planning, thought and a significant budget....27-03-22, 09:46 AM -
Reply to New suspension, front way too highNothing is every perfectly symmetrical, I was asking because 45mm to 50mm of droop travel seems low, I would have thought it would be more than this.
My PB Challenger with Dobinson MT/IMS struts has a 35mm front ride height increase and...26-03-22, 08:50 AM -
Reply to New suspension, front way too highWas the droop measured with both front wheels hanging or was one wheel still in contact with the ground?
I have PM'd Redbruce to get his suspension geometry calculations as they are different from mine, because the strut is at a 12 degree...25-03-22, 11:43 PM -
Reply to New suspension, front way too high244mm is what this web page states.
https://dobinsons.com/frequently-asked-questions
I seem to recall the measurement that Dobinsons give is the minimum setting to allow clearance between the strut and the UCA.
Struts must be...25-03-22, 11:04 PM -
Reply to Jack and Axle standsMy trolley jack only lifts to 500mm high so I have a hard rubber hoist block to make up the shortfall in lift height.
Look at Page 14 of this catalogue;
https://www.hoistparts-australia.com...n-Ward-Assoc-T...24-03-22, 10:16 PM -
Reply to OZ Tech Suspension for NXHi Matt,
Nothing wrong with a OzTec Kings combo suspension but coil selection is critical.
Can we assume that you are after a modest lift so front ride heights 535mm +/-5mm and rear ride heights 575mm +/-5mm when unloaded?...23-03-22, 10:46 PM -
Reply to Fulcrum Formula Suspension kitHi Turbopsi,
I do not like seeing people get stitched up by the so called experts in their field.
Your fixed price installation will be just that, because they can install the suspension without touching the alignment adjuster...22-03-22, 09:49 PM -
Reply to Fulcrum Formula Suspension kitHi Turbopsi,
"You also need to have the sonic generator recalibrated and the inside of your tyres sealed". Mate you are being upsold and told BS, walk away from these people.
Gen 3/4 Pajero factory suspension arms...22-03-22, 04:43 PM -
Reply to Changing Tyre ProblemChanging over tyres and wheels will not effect the wheel alignment if the overall tyre diameter is the same.
However if your off road tyres have a larger overall diameter the effect on tyre wear of any toe or camber error will be greater.
...21-03-22, 09:50 PM -
Reply to Fulcrum Formula Suspension kitHi Turbopsi,
I ran Bilstein struts and shockers on my Challenger for just over 90,000kms, I found the on road handling excellent, but off road the suspension was too hard because the dampener compression rate were too firm and the rebound...21-03-22, 03:53 PM -
Reply to Changing Tyre ProblemThis is a common problem with alloy rims that are hub centric. I know when I first got my Challenger in 2011 and changed to LT tyres after I drove it away from the showroom, the amount of corrosion between the steel disc hub and the alloy wheel was surprising....21-03-22, 10:58 AM
-
Yes Gen 3 and 4 springs are interchangeable.
OJ.20-03-22, 03:00 PM -
Reply to Fulcrum Formula Suspension kitStruts and shockers are the most difficult choice because there is very little information available from manufacturers/suppliers on compression and rebound valving rates.
At least with coils if you can find out free lengths and spring rates, so...19-03-22, 05:55 PM -
So can it be opened manually also?
OJ.19-03-22, 02:02 PM -
Reply to Jack and Axle stands508mm max lift is too low if you want to jack the rear of a Gen 3/4 so both rear wheels are off the ground, using the centre of the rear diff carrier. You need 525mm for stock suspension and 575mm for extra heavy duty suspension and 1 diameter up in...18-03-22, 06:31 PM
-
-
Are you referring to the electric unlocking system or the power tailgate that is available on some of the up spec Pajero Sports?
The electric unlocking has a manual override, there is a small access cover in the lower centre section of the...18-03-22, 02:55 PM -
Unfortunately most aftermarket coils have a higher spring rate than factory coils so softer coils would need to be custom made, problem with this is the lighter spring rate coils will sag and loose ride height over time, even the factory coils sag in...17-03-22, 11:04 PM
-
Hi Grumps,
There are very few aftermarket alloy or steel rims that will legally fit on a Gen 3/4 Pajero. You need to check front brake caliper clearance, centre bore diameter is 67.1mm and the offset is P46.
In theory you can widen...17-03-22, 10:09 PM -
Last year I was contacted by an Adelaide based PB Challenger owner from the forum about the poor handling of his suspension upgrade using Tough Dog adjustable struts and shockers. We had a meet up and drove each others cars to compare the comfort and...17-03-22, 01:48 PM
-
Reply to Alloy bullbar - can it be painted ?Any paint will chip off especially if venturing off road, powder coating will last longer if the correct material and process is used.
Preparation prior to any painting or coating is critical and effects the long term durability of the surface...17-03-22, 10:51 AM -
Reply to New BrakesThere are significant differences between the design of the braking system between a PB/PC Challenger and a Gen 4 Pajero, that need to be considered before any hydraulic component upgrade is done.
PB/PC has a vacuum operated brake booster...17-03-22, 10:46 AM -
Reply to Inlet Manifold and EGR Clean QuoteThe engine is torque limited 350Nm to protect the auto trans, but the manual has 400Nm of torque.
A mild ECU tune would recover the missing 50Nm and not put any extra load on the engine or driveline except the auto trans.
I suspect the weak...16-03-22, 05:50 PM -
Do 80 series run the same coil diameters front and rear?
You would also need to know the internal and external diameter of the factory rubber spacers and how critical these dimensions are, then cross check on the spacers you are looking at fitting,...16-03-22, 12:25 PM -
Have you weighed your rear axle?
What thickness spacers are you thinking of?
I haven't looked closely to see if spacers will work with the EHDVR coils with its inverted design, my initial concern would be maintaining upper coil location....16-03-22, 11:14 AM -
Hi Martin,
I received and email response back from Marshall overnight, to your question/suggestion.
" I experimented using lockup in D (4L) and found it was too dependent on terrain to work properly. Sand Vs creeks vs...16-03-22, 08:14 AM -
It could well be possible.
I will need to talk to Marshall and have a serious think about the benefits and disadvantages of having Auto Mate operating when in low range and in Drive.
Certainly in low range when climbing difficult and...15-03-22, 07:24 PM -
Reply to PB Challenger OverheatingThe radiator cap seals and pressurises the radiator to about 127kpa, this is to increase the boiling point of the coolant.
When the pressure in the radiator exceeds 127kps, due to the coolant heating up, the radiator caps internal valve opens up...15-03-22, 05:27 PM -
Axle seals will only seal correctly if they are the correct and quality part, it is installed correctly, there is no damage on the axle where the seal contacts and the diff breather is open and clear.
OJ....15-03-22, 05:11 PM -
Reply to Towing on a hot dayOr you can just flick the gear lever over to sports mode and keep it in 4th.
OJ....15-03-22, 12:01 PM -
Reply to Inlet Manifold and EGR Clean QuoteJaycar is your friend.
https://www.jaycar.com.au/3-9k-ohm-0...rt=3.relevance
EGR systems are deigned to reduce emissions when the...15-03-22, 11:56 AM -
Reply to Towing on a hot dayMost manufacturers only want to spend the minimum amount of money on development so they can get their product to market quickest and beat the completion to the "now sales dollar". The marketing arm of any vehicle manufacturer will have a much...15-03-22, 10:32 AM
-
Hi Martin,
I have done a reasonable amount of very soft sand driving and always use Auto Mate in manual mode and low range, my tyre pressures are set a 12psi cold with LT235/85R16 Cooper ST Maxx. tyres. I would only see 100C+ on a really...14-03-22, 09:12 PM -
Hi Niks,
Are you looking at the Coopers UK website, the range of tyres is different in the UK to other countries, AT3 LT's are not listed on the Coopers website.
Listed options are.
AT3 4S 265/65R18 114 passenger construction....13-03-22, 12:18 PM -
Reply to Filter serviceHi Hup,
After a filter change it can take up to 50 or so pumps of the hand pump before it goes hard, this should be done at a slow to moderates pace and not super fast, so it takes several minutes for the hand pump to go hard and can no...12-03-22, 06:34 PM -
Reply to Monroe TDT rear shockers install.12-03-22, 04:16 PM
-
My best mate has a MY13 NW and I fitted a set of King standard height heavy duty coils about 7 years ago as the factory coils where not handling the rear cargo area loads of 150kg and camper trailer towball loads 100kg. He had the left shocker replaced...12-03-22, 02:39 PM
-
Late last year "Pajero 12" (the Apprentice) fitted a set of OzTec rear shockers to his NW as one of his Bilstein's was shot after 100,000+kms, he decided to do this without my assistance, thinking that he has enough experience to do this by...12-03-22, 02:10 PM
-
Reply to error P0428 - o2 sensor help!Hi Pete,
Sorry I cannot be of much more assistance as I have very little experience with the Mitsubishi DPF systems. I do seem to recall that using the incorrect engine oil can cause problems, so has the oil been changed recently?
...11-03-22, 06:54 PM -
Reply to error P0428 - o2 sensor help!P0428 is not a Mitsubishi V6 EFI code but it is a 3.2 DiD code that is related to EGT sensor and the DPF system.
http://faq.out-club.ru/download/paje...3/index_M1.htm
OJ.11-03-22, 06:14 PM -
Take it back straight away, brakes are not something not to take chances with.
Noisy brakes = Brake problems!
OJ.11-03-22, 03:08 PM -
Reply to Inlet Manifold and EGR Clean QuoteThe Thermistor is incorporated in the MAF sensor, the thermistor is left in place, it is just electrically disconnected from the Engine ECU in the wiring loom.
OJ....11-03-22, 02:51 PM -
Reply to 3.2DiD oil dipstick questionAccording to Partsouq, the part number for a 2004 3.2 DID dipstick is 1255A144 cost just over $20 + freight.
https://partsouq.com/en/catalog/genu...fHwhKzI-c3d9T3...11-03-22, 11:02 AM -
Reply to Rear Jack Stand PositionIf I am working with a trolley jack and jack stands, and not a hoist, I prefer the safety and stability of working with only a single wheel off the ground.
OJ....10-03-22, 10:56 PM -
Reply to Rear Jack Stand PositionYes, this is where I locate the rear jack stands on Gen 4 Pajero's when I do suspension work. It is also a good idea to place the removed wheel directly under the same subframe just forward of the jack stand, so if the vehicle falls off the jack stand...10-03-22, 10:10 PM
-
Reply to Pajero subframe drop/body liftHi NS07Shorty,
How are you compensating for the increased working angle of the driveshaft joints, when you increase the wheel travel?
OJ.10-03-22, 09:59 PM -
Reply to Is it worth buying a new car now?I am not sure how much the OzX Corp system weights but a 16kW/h battery is around 160kgs and I would think a hub motor/generator might be 25kg each + associated electronic control gear and wiring, another 25Kg so a total of 235kg to maybe 250kg in added...10-03-22, 04:02 PM
-
Reply to Is it worth buying a new car now?There is a Melbourne company of very smart engineers that have developed an electric hub drive motor system, with regenerative braking, stability control, solar panels and battery storage that is fitted to caravans that significantly reduces fuel consumption...10-03-22, 03:20 PM
-
Reply to Is it worth buying a new car now?HI Dicko,
It will depend on if you can find an electric or hybrid vehicle to do the job you need it to, how many kms you drive a year in this vehicle and the purchase price of the vehicle.
I looked at this 2 years ago when we...10-03-22, 11:05 AM -
Reply to Determine body lift or not?A Gen 1 & 2 Pajero's has a body on chassis construction so I think the bumper is attached to the chassis and not the body, if this is correct then you will need about a 15mm gap between the bumper and the body to allow for chassis flex otherwise...10-03-22, 07:38 AM
-
Reply to PB Challenger Seat SpacersNo need to manufacture anything.
Just remove the acorn nuts that are used to attach the seat rail to the M10 stud on the floor pan, then screw on and tighten a M10 x 1.25mm pitch coupling nuts to the front seat attachment studs, and then attached...09-03-22, 09:37 PM -
Reply to Battery ProblemsI have tong tested the parasitic draw on my PB Challenger, and when it is locked it is around 100 milliamps and when unlocked it is around 400 milliamps. My tong tester only measures in 100 milliamps increments, so there will be some error. I have Auto...09-03-22, 12:30 PM
-
Reply to Battery ProblemsI also recall Marshall from MM4x4 finding out that some plug in devices that are connected to the OBD2 port can keep the CanBus awake and have a high parasitic current draw.
OJ.09-03-22, 09:59 AM -
Reply to Inlet Manifold and EGR Clean QuoteYes, that all you need to do, "Scouts Honour".
It is that simple
OJ....08-03-22, 04:44 PM -
Reply to Inlet Manifold and EGR Clean QuoteHi Hayzelnut,
In my opinion an electronic EGR off is a must, I am not sure what method the plug and play units use but a few of the older units have been having problems. I did a DIY resistor mod, and if you can cut and strip 2 wires, solder...08-03-22, 02:17 PM -
Thanks Hayzelnut,
Auto Mate should keep the ATF temperatures under control and extend the life of the ATF, heat and heat effected ATF are what kills Auto's.
OJ....08-03-22, 12:31 PM -
Highly likely to be more than 1 blown fuse, so check every fuse inside the cabin and under the bonnet.
Some circuits have up to 5 or more fuses that are required for the correct operation of the ECU's that control so many things!
...08-03-22, 10:45 AM -
So has the ATF flush changed the behaviour of the auto?
OJ....08-03-22, 10:40 AM -
08-03-22, 08:30 AM
-
Reply to Auto showing D & N at same timeHi Pajerox,
It is most likely either the inhibit switch or the control cable or both that are out of adjustment or sticky indicator switches on the gearbox.
Is your auto a Jatco V5A5A or Aisin V5AWF ?
OJ.08-03-22, 07:07 AM -
Hi Nik,
Some Euro/Overseas Gen 4's came with lower suspension, front coils are 10mm lower and rear coils 6mm lower so the factory ride height can be around 485mm to 490mm and the rear ride height 515mm to 520mm. Ride heights are measured...08-03-22, 06:51 AM -
Reply to Camper trailer hire.06-03-22, 07:22 PM
-
You will really appreciate the coil performance and the 5899 rubber assist cones when fully loaded to max rear axle weight and travelling over rough roads.
From the photo of full compression the 5899 cone is not contacting the coil pad yet, and...05-03-22, 07:51 PM -
Auto Mate is the main reason I still own a PB Auto Challenger, without Auto mate it would have been moved on many years ago. Currently no plans or reasons to consider changing it over as it still does everything I need with comfort and reliability....05-03-22, 07:43 PM
-
I tend to drive with my headlights on most of the time around the city and suburbs and always when travelling on country roads, it just increases your visibility 10 fold at least!
If you start taking note of how soon you can see approaching traffic...05-03-22, 10:06 AM -
Hi Dicko,
I have been looking into doing a DRL mod to my factory fog lights for sometime.
I have had factory fog lights on previous cars (Honda and Toyota) and both were useless in fog, however I find the Mitsubishi factory fog lights...03-03-22, 09:08 PM -
Reply to Bash platesForum member "Pajero 12"had a genuine MMAL steel bullbar fitted, he had a minor collision with the rear of another car, and the bar was fine but the brackets distorted and the bar folded back into the top edge of the bonnet.
O...02-03-22, 11:22 AM -
Reply to Bash platesGenuine Mitsubishi accessories are designed to minimise the effect on airflow so you should be ok.
OJ....01-03-22, 07:04 PM -
Reply to Bash platesI consider the design of the Kaon plates to be best in regards to airflow to the intercooler, this is important if you have a split pan design bullbar (ARB, TJM, OL, Ironman, MCC, etc) much less of an issue if you have no bullbar, factory bullbar or...01-03-22, 06:42 AM
-
Reply to HowYes! Remove the bolts and polish then up or replace them with new bolts and either assemble with marine wheel bearing grease or anti seize.
I have had to cut these bolts out and change bushes, on a NW that only had 75,000kms on the clock, but it...01-03-22, 06:38 AM -
Correct, lower fuel consumption, lower ATF temperatures, lower engine coolant temperatures, lower engine air inlet temperatures combined with an increase in ATF life and this must also lead to an increase in both Transmission and Engine life because...28-02-22, 05:45 PM
-
Welcome to the "Choir of Converts".
OJ.28-02-22, 03:19 PM -
So what are they being replaced by?
Nitto Ridge Grappler?
Mickey Thompson ATZ P3?
Goodyear DuraTrac?
Cooper ST Maxx?
or back to Kumho MT51?
OJ.27-02-22, 07:27 AM -
Exped self inflating sleeping mats at 50% to 60% of normal RRP.
https://k2.com.au/collections/campin...m_term=0_ee9e9...27-02-22, 07:22 AM -
Reply to Will Triton Wheels fit my 06 NS?Hi Benckj,
PCD and centre bore are the same with P46 and P83 genuine factory alloys.
OJ.26-02-22, 04:08 PM -
Reply to Canning Stock Route in 2022?Hi Aspirio,
The CSR is not for the inexperienced or even experienced independent traveller, you need to be very experienced in remote area travel, this is a long remote and logistically difficult trip that should only be undertaken by the...26-02-22, 12:25 PM -
Reply to Will Triton Wheels fit my 06 NS?Since they are 18" rims then they are highly likely to fit over the front brake calipers, if they were 17" then the chances would be reduced, either way it is worth a test fit to the front axle to check clearances.
Trion rims have a P38...26-02-22, 06:41 AM -
Reply to Today, my Challenger died.Are sure it hasn't, broken the balance belt that sits behind the timing belt, this can take out the time belt and then cause the engine to destroy itself, if it happens at speed?
I would be checking the balance and timing belt first, then taking...25-02-22, 08:20 PM -
Reply to Fitting steel mesh platformIn principle, by reducing the number of failure points and spreading the loads over a greater number of points is a good thing, and makes engineering sense.
However U bolts are not the ideal method of attachment if the vehicle is going off...24-02-22, 01:07 PM -
Reply to Canning Stock Route in 2022?Agree with Sharkcaver, CSR permits not being issued for 2022 and highly unlikely to be issued until COVID 19 is no longer a threat to remote communities.
OJ....24-02-22, 08:36 AM -
Reply to Pajwingshttps://www.emuwing.com.au/product/g...en4-2006-2021/
https://www.pajeroforum.com.au/forum...ss-back-access
OJ.23-02-22, 08:48 PM -
Reply to Pedders 5899 Install and Flex TestHi George,
16mm left to right, is quite a lot for factory coils.
Was the vehicle parked on level flat ground, both longitudinally and laterally, when the measurements were taken?
How much fuel is in the fuel tank?
...23-02-22, 07:31 PM -
Reply to Brakes vibratingIf they are the Bendix 4wd pads with the Titanium strip then no bedding is required according to Bendix..
https://www.bendix.com.au/product-range/4-wheel-drive
BLUE TITANIUM STRIPE
No bedding-in required, meaning less...23-02-22, 07:19 PM -
Hi Old Pops,
Since you are also in the UK, are your Widpeaks the AT3WA and not the AT3W we get in Australia?
OJ....23-02-22, 09:09 AM -
Reply to Pedders 5899 Install and Flex TestHi George,
What are your rear ride heights?
Measure from the centre of the wheel hub to the underside of the wheel arch in a vertical line, vehicle must be on flat level ground.
Unladen rear ride height specification for a Pajero...22-02-22, 08:30 PM -
Reply to Switch off EGR for $1Kingbrown is on the money, with this.
From my testing the best method of doing the EGR off mod is to remove the thermistor out of the circuit completely and replace it with a 3.9Kohm 0.5W Metal Film Resistor that connects together the Yellow/Blue...22-02-22, 09:29 AM -
Reply to QF Bull Bar optionsAt 105kg packed weight it must weigh 95KG! That is twice weight of a 42kg winch compatible Smartbar.
It does however have a separate winch cradle which I would assume is made from steel and the same with the mounting brackets.
Fitting Instructions;...22-02-22, 08:45 AM -
You said you definitely did not want secondhand, but since these are being sold as genuine Denso injectors with less than 10 hours running time and at less than half the cost of new items from Partsouq, I thought it might be worth letting you know. You...22-02-22, 07:21 AM
-
22-02-22, 12:13 AM
-
Reply to Pajero subframe drop/body liftAm I correct in thinking that a subframe drop does not increase the under diff ground clearance, but it does increase approach and departure angles, and increase the ramp over angle.
It may also allow for larger diameter tyres to be fitted but...21-02-22, 09:19 PM -
Hi Niks,
The Outpost AT seems to be the new replacement for the Rotiiva AT and is slightly more aggressive and stronger.
There is also a new Outpost APT which appears to have a milder tread pattern than the AT.
https:...21-02-22, 09:36 AM -
Hi Niks,
All manufacturers have bad batches of products from time to time, it is how they handle this problem with the consumer that determines if you end up with a loyal customer or one that tells a thousand people how bad your brand and...21-02-22, 07:04 AM -
Reply to Challenger ServiceElectronic EGR off is the best option on the PB/PC Challenger.
https://www.pajeroforum.com.au/forum...r-resistor-mod
Options are a plug and play cable/module or a 15 minute...20-02-22, 09:05 PM -
You must be doing something wrong to wear out a set of the Bridgestones in 20,000klms! (697,s) I,ve a set on the NW and have been used mainly for towing. 55,000klms and I reckon good for another 10,000klms. Great tyre in the wet. We get a lot more wet...20-02-22, 09:00 PM
-
As good as Auto Mate and Auto Mate Pro are, the units are reactive to the changing conditions, it cannot see the road ahead and make decisions in advance. Using Manual Sport Mode of Auto Mate, Auto Mate Pro or Lockup Mate ensures you are in control of...20-02-22, 08:44 PM
-
Reply to suspension birthdayHi Moe,
265/70R17 is a common plus 1 size that many use but depending on the tyre brand, model and tread wear they can rub in tyre plastic trim of the spare wheel cover and if you do not have a bullbar then the tyres can rub on the inner...20-02-22, 08:40 PM -
Hi Niks,
Since you are in the UK and want a good on road wet weather tyre with some mild off road capacity, I would suggest you consider Pirelli All Terrain Plus, in either 265/60R18 or 265/65R18.
OJ.20-02-22, 03:28 PM -
Reply to Towing with ns 3.2 manualHi Redbruce,
Have you tried using the Load % parameter on your Scangauge II, the lower the Load % the lower the fuel consumption for a given speed.
OJ.19-02-22, 08:15 AM -
Reply to What is this?It is the vacuum control for the inlet manifold swirl valves.
From the Technical Manual
SWIRL CONTROL VALVE <4M41>
The swirl control valve closes one of the intake ports during intake stroke. This creates a strong swirl...18-02-22, 03:55 PM -
Reply to Best Air compressor?Hi Jaffles,
Under bonnet temperature could easily be 50C to 70C before you even start using the compressor so its electrical performance will have already been down rated and then you are compressing hot air which is less dense. Have you...18-02-22, 07:08 AM -
I replaced the Bilstein with Dobinson MT, these are the earlier version of the new IMS range. They have been fitted for just over 60,000kms so far and about 1/3 has been off bitumen and at GVM to GVM+150kg. No problems to report, they are softer on compression...17-02-22, 05:31 PM
-
Reply to EFS Coils Sagging??Looking at bothe the spring rate and free length, these coils should give a 40mm lift over standard coils for the same load, if they are made to specifications.
EFS coils have a 3 year/100,000km warranty, and given that they are not providing...16-02-22, 10:58 PM -
Reply to Best Air compressor?Not the cheapest or quickest compressor around at $350 but the ARB single cylinder compressor CKMA12 is a compact and lightweight unit is a proven long term performer, which only draws up to 50 amps at full load, and has a 100% duty cycle so it will...16-02-22, 10:23 PM
-
Reply to Pedders Suspension. What's it worth?You might get 1/4 to 1/3 of the price of the parts only if someone wants this particular setup.
Did you record the ride heights and the axle weights when they were fitted on the vehicle?
OJ....15-02-22, 05:50 PM -
Reply to PS My18 (7Seat) Spring ConfirmationThanks for the update Newboy.
What rear coils did you end up fitting, KCRR-38?
Also assume you have decided not to change the front suspension at this point in time.
OJ.15-02-22, 05:46 PM -
Reply to Pedders Suspension. What's it worth?How many kms on the Peddars suspension?
is it standard height heavy duty?
OJ.15-02-22, 02:45 PM -
Reply to House electrical question-Electricity- the silent and invisible killer!
OJ.15-02-22, 09:16 AM -
Hi Gimmo,
All good info provided by others, above. From an Auto Challenger specific experience.
1. Tyre pressures, I regularly run 12psi in my Cooper ST Maxx 10ply LT tyres when fully loaded and in very soft sand, just keep...14-02-22, 02:06 PM -
Hi John,
I suggest you consider Auto Mate Pro, this is the 3rd generation of Smart Torque Convertor Lockup control, by Marshall from MM4x4.
Once you have driven a Gen 4 with Auto Mate Pro, you will be converted and wonder why you didn’t...12-02-22, 09:21 PM -
Reply to Electric park brakeGreat outcome and good to see the Dealers and MMAL step up and accepted responsibility.
Thanks for reporting back GGG, it gives others knowledge and also confidence to push for warranty repairs when they are legitimate.
OJ....12-02-22, 05:16 PM -
Reply to PB Challenger OverheatingGenuine Radiator part Number is 1350A923
Cost is about $1000 + freight from online suppliers like Partsouq or other online parts suppliers, so I would imagine a genuine radiator from a Dealer would be $1500 to $2000, ouch!.
Found this for...11-02-22, 09:41 PM -
Reply to What are your temperatures?After the vehicle has sat overnight and not been driven, all temperatures should be within a degree or 2, if not the offsets need adjusting.
OJ.11-02-22, 08:37 PM -
Hi John,
I think with a bit of fine tuning you can get what you desires=.
1. When unloaded run the airbags at 5psi, this will reduce the rear ride height and spring rate.
2. when loaded and hitched run the airbags at 20-25psi,...11-02-22, 08:34 PM -
Reply to PB Challenger OverheatingFactory Specifications from the Technical Manual.
...Radiator Pressurized corrugate type 11-02-22, 08:21 PM -
Reply to PB Challenger OverheatingNo problem Hayzelnut.
Marshall and I spent hundreds of hours, tens of thousand of kms of drive testing and several years to get to the current version.
It takes a few days the the INVECS II Adaptive Learning of the factory AT...11-02-22, 12:22 PM -
Reply to Rear Suspension AdviceHi Wes,
Considering your normal rear axle load, plus the extra loads when on atrip and the front suspension ride heights, then I would be looking at getting the extra 10mm free height, if Universal can make the coils to the same specifications...10-02-22, 10:00 PM -
Reply to Lifting Spare wheelAL-KO make a very low profile 50mm ball off road hitch rated at 3500kg. It is under $300 and can be used with a WDH when not off-road.
https://alko.com.au/product/solution...ball-coupling/
OJ.10-02-22, 07:44 AM -
Why do the water pump, if there is no sign of coolant around the weep hole and its is only done 90,000kms?
Is it noisy? Have you checked it by hand with the belt off?
I am up to 180,000+kms on the original water pump and I am sure there are...09-02-22, 07:43 PM -
Reply to Cargo Barrier for NW PajeroThere are a few 2nd hand units on Gumtree.
https://www.gumtree.com.au/s-parts-a...rrier/k0c18323
OJ.09-02-22, 07:16 PM -
Reply to New main battery - best option?Factory battery is a 95D31L but a 125D31L will most likely fit as this is the size I use in my PB Challenger that also has a factory battery size of 95D31L.
I use Bosch S4 125D31L which is 790CCA and 100AH, cost about $250, current battery...09-02-22, 05:44 PM -
Reply to Turbo replacement on NW.Hi Scooby,
I do not have a NT/NW/NX in the driveway to test but I did look at my PB Challenger and the actuator rod moves about 12mm in total, and this makes more sense.
So I looked at the Challenger Service Manual and the instructions...09-02-22, 04:14 PM -
To flush and refill to ATF it can take between 8 litres and 12 litres depending on how dirty the old ATF is.
The AT pan has a wet gasket so if the pan is removed to replace the screen filter, the sealant must cure for at least an hour or 2 before...09-02-22, 07:32 AM -
As a generalisation, 65 series tyres tend to be mostly light duty passenger construction tyres with a few XL extra load and very few Light Truck construction 8ply/10ply, where 70 series tend to be mainly Light Truck 8ply and 10ply construction with the...08-02-22, 09:10 PM
-
Level with the bottom of the filler hole, 8mm below, 22mm below, 18mm below, 28mm below and 36mm below, what a confusing for those doing the servicing.
Surprised the vehicle does not have to be facing north and only on a full moon, when check the...08-02-22, 06:40 PM -
Reply to suspension birthdayWelcome to sunny SA!
Changing rim diameters or offset will not fix your problem, it is a wheel alignment problem.
Have you driven the Pajero over 80kph since replacing the suspension, if so how does it steer and corner?
Is it...08-02-22, 01:27 PM -
I believe the difference is in the torque convertor specifications, based just on some searching and reading online.
OJ.08-02-22, 01:22 PM -
Reply to suspension birthdayHi Moe,
S.A. South Australia or South Africa?
You do not say what your before and after ride heights are, but you do say the wheels have moved inwards as a result of the lift.
This is because of the IFS and IRS...08-02-22, 08:51 AM -
Reply to Towing on a hot dayI think if someone has dropped over a grand to buy and have installed an Auto Mate Pro, then they are quite within their rights to report back on what they think.
They may need some assistance with fine tuning the settings to get the best out of...08-02-22, 07:23 AM -
Reply to Turbo replacement on NW.Hi Davo,
The approximate 12mm of actuator travel rod travel is ultimately responsible for the total range of the variable inlet guide vane movement that that adjusts for exhaust flows from engine rpms from 1600/1800rpm through to redline...08-02-22, 07:16 AM -
All drain and filler plugs also tend to undo easier when the housings are hot.
OJ....08-02-22, 04:26 AM -
Reply to Turbo replacement on NW.So lets consider how the variable geometry vane turbo control system works.
The turbo has maximum boost capacity of between 28psi and 33psi but only up to 2/3's of this capacity is used.
There are 2 systems that control and...08-02-22, 04:12 AM -
With the low spring rate factory coils I suspect you will get a slight increase in ride height from fitting Bilstein's.
Many years ago there was forum member with a 4x2 PB Challenger, and I seem to recall, that he had fitted Bilstein struts and...07-02-22, 07:53 PM -
All fluids deteriorate over time, heat/cool cycles, moisture absorption, diesel dilution and combustion contamination, so fluids/lubricants should be replaced as per the maintenance schedule as a minimum. Noting the the replacement intervals reduce when...07-02-22, 04:07 PM
-
Reply to PB Challenger OverheatingHi Hayzelnut,
Why not hold off on the radiator until you have the data from the Scangauge II and see the improvement on operating temperatures you get from Auto Mate.
250,000kms is not a lot of kms for the radiator if it has had regular...07-02-22, 11:07 AM -
Reply to Towing on a hot dayHi Mark,
You do not have a signature at the base of your posts so we do not know if your NT is stock, or has fitted accessories like bullbar, winch, underbody guards and driving lights as these all effect the cooling system efficiency. Things...07-02-22, 11:01 AM -
Reply to Rear Suspension AdviceI would go the OME.
Forum member "Ascee" was getting a set of coils made to the CRR-69EHDVR specification +10mm free length for his Pajero Sport, so if you contact him for details and then the spring maker might be willing to make a 2nd...06-02-22, 10:41 PM -
Reply to PB Challenger OverheatingSuggest you contact Ultragauge to check compatibility of the MX1.4, if it suits MN Triton or Pajero Sport with the 2.5lt CRD 4D56 HP engine then it is suitable for the PB/PC Challenger.
I haven't tested an Ultragauge MX1.3 or 1.4 in my PB Challenger...06-02-22, 08:52 PM -
Reply to Rear Suspension AdviceI do have a calculated estimate of theoretical working spring rates for the progressive rate coils at any given EBH, I have added to the specs below in orange text..
You can see that the Kings, OME and Lovells all have a similar working spring...06-02-22, 08:45 PM -
Reply to Rear Suspension AdviceHi Wes,
I your first post you posted.
Originally fitted CRS-32s supplied by Ultimate Suspension on recommendation that they would be a better fit than CRR-69HDs. Although the CRS-32s had slightly lower spring rating, they were taller...06-02-22, 05:32 PM -
Reply to PB Challenger OverheatingHI Hazelnut,
The overflow tank is designed to store the excess coolant when the engine is at operating temperatures and the coolant expands, the coolant then returns back to the radiator when the engine cools down.
The noise...06-02-22, 11:12 AM -
Reply to Towing on a hot dayHi Mark,
My PB Challenger was and is used by MM4x4 as the "test mule" and when Marshall has the Challenger, I normally swap and get his NX with the latest version of his product for a few days, so I have driven his NX with Lockup...03-02-22, 04:04 PM -
Reply to Camber adjustment bolts seizedHi Bruce,
Start spraying both side of all adjusters, once or twice a week, for the next 6 to 8 weeks with a penetrating lubricant like Inox MX3, LPS 1 or WD40, these are what I would normally use.
However there is a WD40 specialist...03-02-22, 02:11 PM -
I have not had the need to disassembled a hand primer pump, but given the pressure they build up I would doubt that they are a diaphragm type pump.
I suspect they are a piston type pump with a piston and shaft seal and also a one way valve....02-02-22, 08:07 PM -
[QUOTE=Toshmegosh;n1101211]
Hi Mark,
Considering the loads and the distribution, it could be worse, does the upgrade use Lovells coils?
545mm front ride height when hitched is manageable, it is when it gets to 560mm or...02-02-22, 02:14 PM -
Reply to Camber adjustment bolts seizedWhen you did this what process did you use?
Front suspension leave struts in place just jack up an support the vehicle, both front wheels off the ground, remove the tyre/wheel the remove, do 1 adjuster at a time, refit but not tighten to...02-02-22, 02:01 PM -
[QUOTE=Toshmegosh;n1101191]
Hi Mark,
Thanks for the reply.
Given the coils that are fitted and your no extra added weight on the front (I am assuming) then the ride heights you have it what I would expect/calculated. Options...02-02-22, 09:38 AM -
Reply to Largest Tyre Size For NX PajeroOME suspension is for those that want the one stop shop solution and a national warranty and support network.
Is OME the "best" suspension for a Gen 4 Pajero?
OME coils are made by Kings to OME specifications, these...02-02-22, 07:03 AM -
[QUOTE=Toshmegosh;n1101173][I]
From VSB-14 NCOP 11, Page 27,.
https://www.infrastructure.gov.au/si...ov_2015_v4.pdf...01-02-22, 10:24 PM -
Reply to Scan GaugeHi Keith,
I would suggest an Ultragauge MX1.4 over a Scangauge II because the Ultragauge is easier to read in daylight, it can display 6 gauges rather than 4 and it has user selectable alarms on many parameters.
Not sure if...01-02-22, 10:11 PM -
King make great springs, but their knowledge of their application is spread over hundreds of different vehicles, whereas on this forum you get real life experiences and feedback.
The Gen 3/4 Pajero with the IFS, IRS, shortish wheel base and longish...01-02-22, 02:51 PM -
A 26mm change in rim offset will increase the swept radius of the steering geometry, so the distance between the hub pivot point and the outer circumference of the tyre will increase so it is more likely to rub at certain steering angles.
...01-02-22, 01:31 PM -
Reply to Towing on a hot dayGreat to see that Auto Mate is looking after your trans temperatures and it will also be reducing you engine coolant temperatures.
At 92C the engine coolant temperature is still in the normal operating range, the thermostat starts to open...01-02-22, 01:23 PM -
There is also the changing in ride height when braking and accelerating due the the change in weight distribution needs to be considered.
OJ....01-02-22, 12:49 PM -
Hi Benny,
Was there also a change in rim offset as well as width?
OJ....01-02-22, 12:00 PM -
The factory front coils have a spring rate of 10.38kg/mm and a free height of 315mm, these ride soft and comfortable but they sag over time especially if any extra weight is added to the front axle.
KCFS-34 spring rate 11.99kg/mm so about...01-02-22, 11:58 AM -
Reply to Camber adjustment bolts seizedThe bush is pressed in to the suspension arm, the outer steel sleeve of the bush is only as long as the width if the arm but about 4mm of rubber and inner steel sleeve that protrudes out each side of the bush. The bolt seizes inside the inner sleeve...01-02-22, 08:12 AM
-
Or incorrect spring and dampening rates, or high tyre pressures, or overloading or driving too fast.
No secret that I do not like airbags but there are plenty of other contributors to major failures both on and off the bitumen.
OJ...31-01-22, 04:48 PM -
Reply to Largest Tyre Size For NX PajeroI hear and read all the time that people get 100,000+ kms from a set of AT tyres, even on a 5 tyre rotation I have never got more than 85,000kms from 5 LT AT tyres! They must be lightly loaded and only drive at low speed on good bitumen roads and run...31-01-22, 04:27 PM
-
Reply to Stuck in 4LLcExcellent, until I researched the problem yesterday was was unaware of the problem or the bush repair.
My Challenger has an old fashion mechanical lever on the transfer case, luckily.
Sports Mode not working, I suggest you remove Auto...31-01-22, 03:16 PM -
Reply to PS My18 (7Seat) Spring ConfirmationYes they look like the correct parts but because of the packaging.
In this thread there is a photo and dimensions of the parts.
https://www.pajeroforum.com.au/forum...r-bags-replaci...31-01-22, 03:09 PM -
Reply to Stuck in 4LLcMi initial thoughts were can the electric transfer case actuator be hotwired back to 2wd?
A quick google search and it can be done.
https://www.youtube.com/watch?v=y6SSzb7OcJk
I would also be checking every fuse...30-01-22, 09:57 PM -
Reply to Electric vehicle doing it easyThe statement from the Qld government states that it will produce 20kg of hydrogen daily using 250 kilowatt solar system.
Given that 1kg of hydrogen is just under 12 litres in volume, that is 240 litres of hydrogen a day.
Hydrogen has an...30-01-22, 09:31 PM -
Hi Andrew,
No surprise to me with your axle weights. To put them in some sort of perspective 150kg is only about 5% overweight and you can maintain reasonable ride heights all be with it with 30psi in the rear airbags so not a disaster....30-01-22, 08:19 PM -
Reply to Wonky idol steep hill low 4wdPossible Causes listed in the Service Manual;
- Improper fuel used
- Fuel contaminated with foreign matter
- Injector leaking or clogged
- Failed injector
- Fuel injection learning failure
- Fuel filter clogged
- Fuel line leaking or clogged
- Failed
30-01-22, 05:55 PM -
Reply to Are these front bump stops?I do not see them listed in the Whiteline Catalogue or Peddars, Mackay, Super Pro or Nolathane.
Genuine Part Number is 4055A008 and they are about $15.00 each + freight, from Partsouq or Amayama or from other online suppliers.
https://w...30-01-22, 05:45 PM -
Reply to Rear Suspension AdviceHi Wes,
Longtime no post mate, hope all is well in your world.
Ultimate Suspension use Lovells coils, and the options are only linear rate with low spring rates of 3.06kg/mm for the CRR-69 and the CRR-69HD so these coils do...30-01-22, 02:24 PM -
Reply to MY19 Sport Exceed - Rear SpringsSince the KCRS-23 results in a ride height about 10-15mm higher than the factory coil when unladen, and the KCRR-23 has the same spring rate as the KCRS-23 but is 20mm and 25mm in free height then you would expect this coil to increase the ride height...30-01-22, 01:55 PM
-
Reply to Largest Tyre Size For NX PajeroLooking at the Maxxis website and the approved rim widths there seems to be some inconsistencies.
The NX has 7.5" wide rims fitted, normally the lower the profile the wider the minimum approved rim width is.
In the table below,...30-01-22, 09:02 AM -
Reply to Wonky idol steep hill low 4wdHi Quinno,
What is is idle rpm normally?
Does the same happen in both 1st low and 2nd low?
Does the same happen in 4Hlc?
Does the same the wonky idle happen on flat ground in low range?
Looking at the circuit...30-01-22, 08:17 AM -
Reply to MONSTA tyresIn OZ they are under $300 a tyre so a similar price to Maxxis.
OJ....29-01-22, 05:16 PM -
Reply to MY19 Sport Exceed - Rear SpringsHi SMO,
It has been 6 months since OlliJ was on the forum so I suggest you send him a PM and hopefully he will reply.
I to would be interested in his feedback.
OJ.29-01-22, 03:29 PM -
Reply to Best roadgoing suspension?So why not look at a larger soft roader instead of a Pajero?
Cheaper to buy, cheaper to run and service, more comfortable.
Kia Sorento for example, is a very nice large soft roader capable of towing modest loads and fine on most dirt roads...29-01-22, 03:25 PM -
Reply to Best roadgoing suspension?On a Gen 4 Pajero the factory spring rates are 10.8kg/mm front and 11.61kg/mm rear, which are quite soft given the weight of the vehicle and the suspension geometry.
I do not have strut and shocker valve rates but to in my onion these are under...29-01-22, 01:06 PM -
Reply to MONSTA tyresTread depth is only one of the critical components in a tyres wet weather bitumen performance, just look how bad a mud terrain with 16mm tread depth perms in the wet weather!
Tread design and tread compound have a greater effect than tread...29-01-22, 12:25 PM -
I am not sure why the additional airbag route was taken rather than a proper spring upgrade to suit the considerable increase in rear axle load.
Whilst airbag supplementary suspension assist of this design may be ok for on highway use it has proven...28-01-22, 08:13 PM -
Reply to PS My18 (7Seat) Spring ConfirmationIf the rear shockers are underperforming after the rear coil upgrade you can expect more bounce on the rebound, it will still feel much different than the soft factory coils that wallow and pitch easily when under load.
OJ.28-01-22, 03:44 PM -
Reply to Largest Tyre Size For NX PajeroAlso need to consider that the spare tyre will also require changing and there are limitations and modifications to the spare tyre cover that also need to be considered.
Mitsubishi 4wds are sensitive to difftyre diameters, even read wear,...28-01-22, 02:03 PM -
Reply to PS My18 (7Seat) Spring ConfirmationHi New Boy,
Welcome to the forum and an excellent 1st post, you have done 99% of the work for yourself by reading and understanding the information that is readily available on this forum.
I would suggest you actually weigh...28-01-22, 01:49 PM -
Hi and welcome to the forum.
There are multiple possible reasons for your problem, so you really need to get a list of fault codes to assist in the diagnostics rather than just start guessing and replacing expensive parts that may or may...27-01-22, 10:37 PM -
Reply to Radiator UpgradeThe engine on the auto Challengers is toque limited to 350Nm but Challengers fitted the manual trans get a 400Nm factory tune. My understanding is the auto was torque limited because of the high slip torque convertor fitted so they could get the torque...26-01-22, 12:14 PM
-
Reply to Radiator UpgradeThanks for the update.
I run Dobinson front coils and Dobinson MT struts and shockers that are the earlier generation of the IMS Monotubes, 60,000kms and no problems so far.
I will look forward to your feedback on the setup,...25-01-22, 09:16 PM -
Reply to Kings LithiumI sent Baintech an email asking if their batteries had BMS on each cell of was the BMS managing a group of cells.
Here is the reply I got.
Thanks for contacting Bainbridge Technologies,
The BMS will manage the cell...24-01-22, 05:08 PM -
Reply to Preparing NP for limited useHi Shopping Trolley,
All tyres form flat spots when left stationary and loaded up, these flat spots do come out of the tyre once the tyre warms up from rotation, but until this you can feel a lumpy ride, it just that it can take some time...24-01-22, 05:01 PM -
Reply to Auto transmission issues.Well I checked the wiring harness and there was a very sharp bend on the conduit just on the chassis side of the clamp.
I removed the clamp and sure enough the taping over the split conduit had broken and the inside of the conduit was full of dirt...24-01-22, 04:50 PM -
Reply to Preparing NP for limited useIf you are not going to drive it once every week or two then.
Change engine oil.
Fill up fuel tank and treat fuel with an additive to stop diesel bug developing.
Pump tyres up to higher than normal pressures do avoid then developing...24-01-22, 02:07 PM -
Unless the OP can borrow a know serviceable pump, then the it would be wise to check the electrical, vacuum and mechanical things first. This should be relatively easily done once he has the information. He could spend serious cash on a new pump and...24-01-22, 08:10 AM
-
Forum Member 4ePikanini seems to have the best knowledge and experience with diagnosing the Gen 3 Diesel fuel control systems.
I do not have a Service Manual so I cannot read up on it. I have read some of 4ePikanini post and it seems these non...24-01-22, 04:03 AM -
Reply to Radiator UpgradeThere are 2 sets of rubber bump stops on the rear suspension.
1, Articulation stops that are on the suspension trailing arms inline with the axle and these make contact with the underside of the chassis, these are not designed to act as...23-01-22, 03:45 PM -
Reply to Weight of second row seatsThe main reason why states are concerned about the removal of seats is it can change to use of the vehicle for a passenger vehicle to a goods carrying vehicle, and this changes its insurance and registration category and chargeable fee's.
It is...23-01-22, 08:13 AM -
Reply to High Air Intake TemperaturesHi Pete,
It seems you are making all the right decisions to take the load of the engine and trans especially when towing.
A few years ago a few of us Adelaide forumites did extensive testing of engine air inlet, coolant and ATF temperatures...23-01-22, 08:05 AM -
Reply to Kings LithiumAs a very earlier adopter of lithium batteries, I will share my experience.
8 years ago, using lithium batteries to run a fridge in a 4wd was considered a waste of money and unproven, yet I took a gamble, based on specifications, and imported...22-01-22, 07:33 PM -
Reply to High Air Intake TemperaturesHi Pete,
Have you considered fitting an EGT gauge?
If your pre intercooler temps are really high then the size of your intercooler could be the least of your problems.
OJ.22-01-22, 01:18 PM -
Reply to Radiator UpgradeBe careful getting airbags fitted, some installers remove or drill the tread out the welded on nut on the upper spring seat, so the airbag valve fits and has clearance.
This is a one way modification and it means the rubber cones cannot be refitted...22-01-22, 12:48 PM -
Reply to Weight of second row seatsThe rules seem pretty straight forward to me.
https://www.vicroads.vic.gov.au/regi...eplacing-seats
OJ....21-01-22, 03:59 PM -
Reply to Radiator UpgradeOver 150,000kms with lifted suspension, on the front 2 different coils and 2 different struts, droop stops reversed and no drive shaft problems, so I see no need to replace front suspension control arms.
OJ....21-01-22, 02:25 PM -
Reply to Mt Adams Track FeedbackHi George,
A club Simpson Trip, High Country or even a CSR is an easier thing to plan, because there is plenty of up to date information on these areas and years of experience to learn from.
The area in the Northern Flinders...21-01-22, 10:37 AM -
Reply to Transmission ECU mappingHave you sent an enquiry to Marshall at MM4x4?
OJ....20-01-22, 08:52 PM -
Reply to P0089 engine code.. driving me mad!Like the saying goes, " if in doubt read the instructions".
OJ....20-01-22, 07:57 PM -
Reply to Weight of second row seatsPreviously reported in this post, 60kg combined for the 2nd row seats.
https://www.pajeroforum.com.au/forum...ght#post603906
OJ.20-01-22, 01:28 PM -
If the number of coils winds is exactly the same then making the free length longer will also slightly increases the spring rate at the same time, so the net effect will be a greater ride height gain than the increase in free length.
I cannot...20-01-22, 01:21 PM -
Reply to Weight of second row seatsI seem to recall reading that the 1/3 seat is about 20ish kg and the 2/3 seat about 40ish kg.
OJ.20-01-22, 01:12 PM -
You will also need the number of turns, wind pitching and wire diameter to replicate the CRR-69EHDVR accurately.
The softer/ lower spring rate coils need to be at the bottom of the spring, this is reverse to how they normally make progressive rate...20-01-22, 09:37 AM -
Reply to Mt Adams Track FeedbackI do not think it is the same track that we did 5 years ago. This area has many disused old mine access tracks, it is extremely tough and remote country and no place for the inexperienced or ill prepared. One wrong move and you are in serious trouble...19-01-22, 10:23 PM
-
Reply to Kings LithiumFrom the Baintech webpage;
"Reducing weight in a RV helps to keep you under the tare weight, reduces aerodynamic drag which improves fuel efficiency while on the road"
Can we all see the problem with this statement? For me this...19-01-22, 11:37 AM -
Reply to Radiator Upgrade130kg of towball weight on 1900kg ATM is roughly 7% so this is good.
130kg of towball load equal about 185kg rear axle load, so 55kg transferred off the front axle and on to the rear, this is also good.
I suspect factory suspension...18-01-22, 11:32 PM -
Reply to Radiator UpgradeThat is one large and heavy camper trailer.
Because the wheels are set so far back and there are large storage boxes forward of the axle, the towball load could easily be over 200kg, even with the rear mounted twin spare tyres and aft of axle water...18-01-22, 09:22 PM -
Reply to Removing MAF sensor - stripped headTry using a 2mm diameter drill bit (new/sharp) and some cutting compound (oil will do if you do not have some) and with a slow drill speed, drill the centre of the screw to a depth of 3mm, then using a Phillips head screw driver with a tip in good condition,...18-01-22, 08:54 PM
-
Reply to Radiator UpgradeHi Goublin,
It will depend on the camper trailer towball load, some camper trailers have less than 100kg and others have over 200kg!
Do you want to do front and rear suspension and get a 30mm to 45mm lift or keep it close to standard...18-01-22, 08:34 PM -
Reply to Kings LithiumFor $170 more I would look at a ITech 120X, 5kg lighter and better performance specifications including a full 3 year warranty..
https://itechworld.com.au/products/1...hoCTOMQAvD_BwE
Most of these "value" lithium's generally...18-01-22, 07:48 PM -
Reply to Radiator Upgrade100,000kms is low kms for a MY12!
Timing and balance belt are due and should not be overlooked, coolant , ATF and brake fluid change also considering the low kms and age, if these have not been done recently.
Factory rear coils are soft and...18-01-22, 07:38 PM -
Reply to Radiator UpgradeHi Goublin and welcome to the forum,
The overheating issues with Challengers has nothing to do with the radiator being undersized or inadequate, The overheating was due to coolant consumption with some engines because of a machining problem...18-01-22, 05:31 PM -
Hi LJ,
These are not a brand of coil, strut or shockers I am familiar with.
What are the finished ride heights at all 4 wheels, when the vehicle is parked on flat level ground?
Measure from the centre of the wheel hub, up in...17-01-22, 02:37 PM -
What struts and shockers are fitted?
Bouncy ride indicate dampening rates are incorrect.
OJ.16-01-22, 08:04 PM -
Sounds like you use the PS well, they really are underrated and very capable with decent tyres, factory RDL, TC calibrated for slow work and deeper low range combined with the 8 speed auto means the trans is not getting hammered or super heated.
...16-01-22, 03:13 PM -
Most likely from the front after the 2nd row sets re folded forward.
OJ.16-01-22, 01:39 PM -
RVCS data lists factory ride height at kerb weight as 520mm front and 559mm rear, so your 565/570mm lifted front height is 45mm to 50mm,above factory, this is at the very upper limit, may be just over, as legally you are required to maintain at least...16-01-22, 01:34 PM
-
Hi and welcome to the forum Ascee,
So looking at the info you provided, and I minus the 120kg for yourself, then that has your PS a 2640kg, split evenly between the front and rear axles at 1320kg each, so 70kg shy of the factory GVM. of...16-01-22, 11:39 AM -
Reply to High Air Intake TemperaturesThe IAT is measured by the #2 Air Temperature sensor located on the throttle body where the intercooled air enters so why not swap the #2 Air Temperature Sensor or check the sensor resistance and also the wiring resistance back to the ECU.
...15-01-22, 11:57 PM -
Reply to High Air Intake TemperaturesHi Pete,
Seems your temperature maybe a bit high and your Dad's a bit low.
Q1. Any bullbars fitted if so what type and to which vehicle? Lights, winches, insect screens, underbody guards?
Q2, Are both vehicles running the same...15-01-22, 07:56 PM -
Reply to Off topic a bit but ffs..If no success park it blocking their driveway, and go sit in the Customer Lounge, make a free coffee and wait or ask to speak to the dealer principle every 15 minutes until you get the service you are entitled to. While you are waiting ring the Number...14-01-22, 11:10 PM
-
Hi Bam Bam,
My comments in blue font within your post below.
OJ....14-01-22, 11:04 PM -
Hi John, please find my comments in blue font within your post.
OJ....14-01-22, 10:18 PM -
The increase in tyre weight will also increase fuel consumption as will a more aggressive tread pattern, combine this with an increase in diameter and the combine effect can be significant even when you make adjustments for odometer readings. Fit a bullbar,...14-01-22, 09:06 PM
-
Reply to Hardkorr BZR 9" mounting.Hi Matt,
Is your problem the overall width of the light? If so have you considered swapping from 9" to &" diameter lights, The 7" "only" has a 1150m 1 lux range compared to 1450m 1 lux range of the 9" but...14-01-22, 08:52 PM -
Hi BamBam,
What suspension setup are you running now and how many kms?
On my PB Challenger I ran Lovells coils and Bilstein struts and shockers for about 90,000kms, on road handling was great but off road the Bilstein's were...13-01-22, 10:31 PM -
Reply to Rear suspension replacement tips..Correct KB thanks for pointing that out, I remember the conversation now. It adds about another 15 minutes to the job and is a good precautionary measure especially if the coils are over 400mm in free length.
OJ....13-01-22, 04:01 PM -
Reply to Budget scan tool for my ChallengerRather than buying a dedicated Scantool, have you considered a OBD2 monitor that also scans and clears fault codes.
Torque Pro is a plugin that bluetooths to a smart phone. Ultragauge MX1.4 is a stand alone gauge that not only monitors engine and...13-01-22, 01:54 PM -
Reply to NX Pajero Standard Eyebrow HeightFront and rear coils are very different and not interchangeable.
Coils can longer or shorter left to right and this is often overlooked if the coils are not marked clearly or the installer is not aware of this.
I also know of people that...13-01-22, 01:48 PM -
Tye noise is subjective.
I regularly drive a NW Pajero that has had ST Maxx tyres fitted for the last 100,000+Kms so I can hear the difference in tyre noise between the Pajero and my PB Challenger that also has ST Maxx tyres fitted. New...13-01-22, 12:33 PM -
Reply to NX Pajero Standard Eyebrow HeightHi Leigh,
RVCS Data indicates factory EBH as 504mm front and 533mm rear.
http://rvcs-prodweb.dot.gov.au/perl/...2016103036.cmd
Agree the front height is ok unless you intend to tow and have towball...13-01-22, 11:30 AM -
Reply to Rear suspension replacement tips..Hi Highace,
The PA/PB/PC Challengers and Pajero Sports all share the same rear suspension and I have removed and refitted coils several times.
The first few times I used spring compressors that I had to modify but I found a way of...13-01-22, 10:22 AM -
The unibody/monocoque construction of the Gen3/4 Pajero is more susceptible to driveline, tyre and road noise that 4wds that have a body on chassis construction.
OJ....12-01-22, 09:21 PM -
I have followed the Paris to Dakar Rally since the late 1970's. Like most motorsport in the 60's, 70's and 80's the vehicles competing where basic production specification with only minor modifications, but as with any motorsport the influx of serious...12-01-22, 08:19 PM
-
Reply to One hit wonders and others.12-01-22, 06:34 PM
-
Reply to One hit wonders and others.You need to get a referral from your GP.
OJ....12-01-22, 06:25 PM -
Hi John,
Welcome, I corrected the thead title, hope you do not mind.
Hopefully you have read the hundreds of posts regarding suspension upgrades on Gen3/4 Pajero's, and you have learnt it is easy to get wrong and difficult to...12-01-22, 12:34 PM -
Reply to One hit wonders and others.Doctors are like mechanics, good for the simple straightforward problems, medical specialist are specialist in their particular field but for complex diagnostics then you need to see a Physician.
OJ....12-01-22, 09:40 AM -
Reply to Sand driving universityComments in blue below
Comments in red
In a Gen 3/4 you cannot turn traction control OFF, you can a should turn stability control OFF, if you are in low range the stability control will automatically turn OFF. However, every time you...12-01-22, 06:14 AM -
Reply to Sand driving universityIn a Gen 3/4 you cannot turn traction control OFF, you can a should turn stability control OFF, if you are in low range the stability control will automatically turn OFF. However, every time you turn the engine OFF and then restart it you need to remember...11-01-22, 10:42 PM
-
Reply to One hit wonders and others.Unfortunately there are not many professional Master Technicians around, this had been brought about by the industry not continuing training the right people and undervaluing what they do but more than happy to charge an average service mechanic out...11-01-22, 07:13 PM
-
Reply to One hit wonders and others.We cannot expect everyone to be on the forum daily as a condition of posting. I think a week is a reasonable time to expect a reply even if it is just an acknowledgement and thanks for the advice given, followed by statement of what they intend to do...11-01-22, 05:01 PM
-
Reply to One hit wonders and others.I do not think it has anything to do with population numbers or migration or generation/age or gender.
I think the problem is most people are in a rush and are after the quick answer/easy fix so they resort to an internet search and jump...11-01-22, 03:59 PM -
The preload of an auto tensioner is to ensure there is the correct amount on tension applied to the belt and the auto tensioner is operating within its mid travel range. Some auto tensioner preloads are set by angular movement in degrees or lineal movement...11-01-22, 11:27 AM
-
So measure the height difference between the awning mounted height and the highest part of the tailgate when lifted up, this will indicate how much the canvas will need to flex up, i suspect it is between 300mm and 400mm. There is a chance that the awning...11-01-22, 07:41 AM
-
Reply to 18" or 17"Hi Redbruce,
Problem with keeping 18" rims is there are limited options of LT tyres available and they tend to be more expensive than the equivalent 17" tyre.
I just did an online quote for Cooper ST Maxx, a proven...10-01-22, 07:39 PM -
As an indication, 4.4Nm is approximately 1.5kg of force applied to a 300mm long lever.
OJ,10-01-22, 06:52 PM -
Reply to NT Family Tourer BuildAgree, I would be installing those guard bolts with the nuts upwards, as there is a very real risk the thread protruding from the nut will be damaged when off road, making it very difficult to remove the nuts when you have to take the guards off....10-01-22, 06:30 PM
-
The 4.4Nm is the preload on the tensioner to get the belt at the correct tension so the auto tensioner functions correctly..
The 48Nm is to torque the bolt that stops the auto tensioner from moving out of adjustment.
OJ.10-01-22, 06:18 PM -
I cannot see how it is possible to have a 270 opening awning open and still be able to use the lift up tailgate of the PS.
OJ.10-01-22, 01:20 PM -
Reply to Falken wild peaks at 3waThe UK Falken website does not list a light truck construction in the sizes you quoted, the 265/60R18 114T is an extra load passenger construction and the 265/65R18 114T are a passenger construction, both tyres have 10mm tread depth.
If you think...08-01-22, 09:58 PM -
Reply to Falken wild peaks at 3waHi Old Pops,
What size and load index are you thinking about?
The Falken AT3W comes in both passenger construction extra load with about a 10mm tread depth and light truck construction 10 ply with a 13.5/14mm tread depth,
These...08-01-22, 07:16 PM -
Reply to Advice or help pleaseAlso the RDL was a selectable option on the base model.
FYI, it is not a straight forward retrofit of a RDL as the axle lengths and I seem to recall spline counts are different, easier to either replace the complete rear axle diff assembly, hub...08-01-22, 07:07 PM -
Reply to hub Broken boltsReplace all wheel studs and nuts, parts will cost about $10 AU per stud, washer and nut assembly if purchased online. Use only genuine parts if possible.
Studs are splined and are pressed in from the rear of the hub and can be replaced whilst the...08-01-22, 06:51 PM -
Reply to Impact drill adapter for wheelsIf you are travelling on dirt roads, especially corrugated, then stop and check the wheel nuts after about 1 or 2 kms, not 100kms.
Why, because the rough road will highlight any problem with the wheel fitment. If a wheel becomes loose on a rough...07-01-22, 03:41 PM -
Reply to Tyre removal and disposalAccording to this website Australia consumes about 57 millions tyres a year and about 69% are already recycled.
A great start and hopefully it will get more each year.
https://www.tyrestewardship.org.au/n...s-end-of-life-...07-01-22, 01:18 PM -
Can we assume you are keeping the 18" rims?
Are you wanting to stay with the standard diameter or go up a size?
Do you want a mild AT or aggressive AT/MT tread pattern?
If you are moving from a light duty HT passenger tyre to...06-01-22, 07:53 PM -
Reply to Tyre shine - opinionsGeneral consensus seems to be water based tyre shines do no harm, except for attracting dust and id too much is used then it gets on the paint work and rims, but solvent based tyre shines may effect the tyre rubber with extended use.
O...06-01-22, 05:09 PM -
Reply to To rotate or not to rotate....Rotate all 5 tyres through all 5 positions regularly.
I use the Cooper 5 tyre rotation method.
https://www.coopertires.com.au/the-c...ing-your-tyres
HT's and mild AT's every 10,000kms.
...06-01-22, 05:04 PM -
Reply to NM/NP Rear Differential LockHi Perri,
I suspect the air pump is the same across the whole Mitsubishi range of Pajero, Triton and Challenger 4wds so you should be able to pick up one from wreckers.
if you know the part number then a quick online search indicates...06-01-22, 04:06 PM -
Reply to Kaiser mechanical rear locker :)Hi Bennie,
I was of the same opinion as you are of it being an auto-unlocker like a Lock-Rite differential but further research indicated this was not the case.
It appears to operate as a normal open diff until there is very significant...06-01-22, 03:51 PM -
I am pretty sure the SWB NS has a Jatco 5 speed auto box with a stall ratio of 1.6:1 so it shouldn't, in theory get as hot as the PB/PC Challenger/MN Triton Jatco 5 speed auto with the 2.04:1 stall ratio. Looking at the Service Manual, there are 2 ATF...06-01-22, 03:29 PM
-
Thanks Bruce for the additional information and clarifications, I did find the Bryan Fry's information/article interesting and learnt a few things.
Unfortunately there is a lot of information that is either wrong, incomplete, generalised or out...06-01-22, 11:05 AM -
Reply to After market inter coolersA few years ago we did some extensive testing in Adelaide comparing Gen 4 intercoolers, bullbars, underbody guards and auto trans lockup's, and there combined effect under high load and high ambient temperature operations.
https://www.pajerofo...05-01-22, 10:29 PM -
So exactly what part of the information Jason posted is incorrect?
I do not particular care about the science behind snake venom, but I do care about the correct treatment of a snake bite and that there is a drug that can be used for all...05-01-22, 10:22 PM -
Reply to Cruise Control Random FailuresErad's line of questioning has merit.
If the Cruise Control light is going OFF when the CC stops working it is different to when the CC disengages and will not re-engage whilst the CC light remains ON.
OJ.05-01-22, 07:07 PM -
Reply to Impact drill adapter for wheelsI would have thought the wheel nut torque on the Gen 3/ 4 Pajero and the Pajero Sport/ Challenger would be the same since they use the same wheel size, but they are not.
Gen 3 Pajero 108Nm +/- 10Nm.
Gen 4 Pajero 115Nm +/- 10Nm
Pajero...05-01-22, 06:59 PM -
Watts divided by Voltage = Amperage.
120 w divided by 12 vdc = 10 amps.
OJ.05-01-22, 10:02 AM -
This is an interesting discussion. It appears they were quite well equipped and had some experience but obviously not enough equipment, knowledge and experience for them to avoid the incident or be able to self recover. We can all learn valuable lessons...05-01-22, 09:41 AM
-
Reply to After market inter coolers02-01-22, 09:29 PM
-
I recently become aware of the potential of a wire chafing problem with the Auto trans wiring harness on PB/PC Challengers and MN Tritons, I was alerted to this by another thread and a linked YouTube video of a Triton/L200.
from the 9 minute mark....02-01-22, 09:22 PM -
Reply to High Country. What do you carry?Hi Gumtree,
The official "Bushwalking Season" is South Australia normally is roughly the 8 months that there is not a total fire ban that closes public access to walking trails that go through private property.
Agree...30-12-21, 10:03 PM -
Reply to Tyre removal and disposalSome interesting reading about Bandag Retreads;
http://www.fundinguniverse.com/compa...g-inc-history/
In 1985 I was working for Dick Lang's Desert Trek Safari's, taking 4wd tours through remote areas of Australia, DL...30-12-21, 06:55 AM -
Reply to High Country. What do you carry?For Bushwalking and remote travel I previously had a SPOT Personal Safety Beacon but the annual cost went to over $300 a year and I did not use the message function often, so a few years ago I brought a KTI Personal Safety Beacon ($240 from Snowys Outdoors)....30-12-21, 06:14 AM
-
All manufactured products have problems or potential, some are known at manufacture and some are not known for years.
When I was in the Aviation Industry, there was an Australian publication called the Aviation Safety Digest, also fondly...29-12-21, 08:43 AM -
Reply to 2012 PB tempSorry I cannot help as I have a Scangauge II because the Ultragauge was not available when I purchased mine.
Rather than asking about the Challenger ask them about 2009 to 2014 Pajero Sport and L200 as these are the global names for the...28-12-21, 11:10 AM -
Reply to Tyre removal and disposalAbout $8 to $10 for a 4wd tyre seems to be the going rate in Adelaide.
Bob Jane T Marts are a part of Tyrecycle, but I am not sure if they will take old tyres if you do not buy new tyres.
Tyrepower also recycle tyres.
Give your local...27-12-21, 09:23 PM -
Reply to 2012 PB tempI would recommend using an Ultragauge MX1.3 because you can display 6 parameters at a time and set visual and auditable alarms, and it is easier to read in strong daylight than a Scangauge II.
Once you have driven with Auto Mate on the...26-12-21, 07:45 PM -
Reply to 2012 PB tempI do not know how to remove the calendar, sorry.
What weight are you towing?
What speed, and gear are you using or just "Drive"?
Any bullbar or aftermarket underbody protection?
Are you talking about engine coolant...26-12-21, 04:37 PM -
Reply to Dipstick "X"I thought it was the opposite, DDDJ.
I was under the impression that the "X" on the dipstick located much higher then the high level hole, was only used for diesel engines with a DPF fitted as it indicated an excessively high oil...26-12-21, 09:01 AM -
Reply to Rear Spring replacementCorrect, shorter free length and higher progressive spring rates of the KCRS-35 results in an unladen ride height increase of about 10-15mm more than new factory ride height but with much better load carrying ability with only a slight decrease in empty...24-12-21, 10:58 PM
-
Reply to Acid for a deep cell lead batteryWe used to "revive" light aircraft batteries to extend their life, by filling full of distilled water, charging hard for a few days to shake the sulphate off the plates, then drain and rinse the battery out several times before filling with...23-12-21, 11:09 AM
-
Similar thing has recently happened to others that have driven through water.
1. Check the mechanical adjustment of the inhibit switch.
2. Disconnect all AT wiring loom plugs clean and inspect.
3. Check inside the corrugated conduit...21-12-21, 10:36 AM -
Reply to 18 to 17 inch rims.Hi Peter,
Bendleby Ranges is tough on tyres, on our last trip, 2 vehicles in our group ruined a tyre each, a Bridgestone D697 and Mickey Thompson AT38 neither were 10 ply light truck construction.
10ply LT tyres are less comfortable,...21-12-21, 10:11 AM -
Reply to Acid for a deep cell lead batteryAGM batteries should also be vented because under some high charge and high heat conditions they will emit hydrogen gas.
From Fullriver Installation Manual.
https://resources.fullriverbattery.c...xternal-media/...21-12-21, 06:40 AM -
Reply to 18 to 17 inch rims.Since you do not want to change the spare tyre and you do not go off road so is there real reason why you should think about going up a diameter tyre.
Plenty of light/medium duty 265/65R17 mild AT tyres available.
OJ....20-12-21, 07:56 PM -
Reply to Lockup kit giveaway!X2 for "flywheels" contribution.
I have had Lock Mate and then Auto Mate fitted for almost 3 years and 62,000kms, that little blue switch light still brings a smile to my face every time I drive the Challenger and when I refuel...19-12-21, 09:21 AM -
Correct, an isolator achieves the same level of electrical safety but it does not give you easy access to the solenoid connections from maintenance or if a solenoid fails and you need to bypass it.
Other thing to consider is how ease the...19-12-21, 09:16 AM -
I would strongly suggest that on any winch fitment that the solenoids are mounted remotely under the bonnet. This means that the 2 wires going to the winch motor are not always live, this is safer in an accident and easier to service and bypass the solenoids...19-12-21, 01:55 AM
-
Reply to Yet Another Rear Storage SetupI will come clean!
My fixed storage system is all 3mm structural marine grade aluminium but the storage boxes that replace my 2nd row seat, that are fitted for longer trips are made from 10mm marine ply.
Thie biggest contributor to weight...17-12-21, 02:11 PM -
Reply to Yet Another Rear Storage SetupThoughts from an old metal worker, aluminum will absorb the heat from the fridge motor and fan, and dissipate it quicker than wood, ventilation is critical for fridge correct fridge operations especially in warm/hot climates.
OJ....17-12-21, 12:10 PM -
Reply to Auto transmission issues.Great find Tone 13
It make sense, who would have thought it was an internal loom wiring problem.
I will be checking the wiring and modifying it on my 10 year old 180,000km auto PB.
Prevention is better than cure!
OJ...15-12-21, 07:01 PM -
Reply to My Auto-mate just arrivedWell done, someone has read the owners manual!
These Auto Mate/Auto Mate Pro lockup kits are really very smart, if you have one and haven't read the owners manual for sometime it is worth a read to refresh the memory of all the features and adjustments....15-12-21, 03:55 PM -
Reply to Auto transmission issues.Agree with Geopaj re replacing the clock spring ASAP.
The gearbox problems are unlikely be related to the paddle shifters/clock spring because the paddle shifters are fixed to the steering column and do not rotate with the steering wheel...15-12-21, 01:47 PM -
Reply to 18 to 17 inch rims.A 245/70R17 is exactly the same diameter as the factory standard 265/60R18 so any increase in fuel consumption will be due to a heavier tyre with a more aggressive tread pattern.
OJ....14-12-21, 08:55 PM -
Reply to Driver seat .Jump on partsouq.com, put in your VIN and then find the part number, I did a general search;
https://partsouq.com/en/catalog/genu...SVhuFXczOncDIR luSSUxERYIeXZ7emh7RDRsPWp1bBNpOjpnbXR6NTE7CTA0bCZ1 bBNqY2wqJTQiJg0ICHsBeAhzVzoobS0ganV9ZWljOj5te3plf3...14-12-21, 06:16 AM -
Avan's have their fair share of loyal owners but like all products there are also a group of unhappy owners, just like Mitsubishi 4wds.
"Off-road" campers and caravans get dragged over some really poor roads so unless the tyre...13-12-21, 10:33 PM -
Reply to the Pic of the Day threadCompared to the northern waters of Australia the south coast water is always cool, it is between 14C and 17C so it is refreshing, due south is Antarctica!
Brisbane water temperature is between 20C and 27C, Cairns 24C to 30C and Darwin 24C to 32C....13-12-21, 07:58 PM -
Reply to Zero offset wheelsIt will also mess up the self-aligning torque characteristics so stability and handling will deteriorate substantially.
Expect unwanted activation of the ASC system particularly when off the bitumen.
Looking at the NZ rules it appears...13-12-21, 01:59 PM -
Reply to Transmission change.Did the torque convertor get changed over?
Did the all the original switches and sensor get reused?
What is the gearbox model number?
OJ.10-12-21, 07:17 AM -
Reply to Second battery graphAgree with Dicko, it could be a battery balancing/equalising between the main and aux battery if they are of different size/capacity and have a voltage sensitive cutout control.
OJ.09-12-21, 12:08 PM -
Reply to Changing rear brake padsThe Pajero Sport has the same rear brakes as the PB/PC Challenger and these are known for wearing the left hand rear brake pads more that the right hand rear.
I am not 100% sure of the reason, if both caliper slide pins are free but I seem to recall...09-12-21, 12:05 PM -
Reply to Changing rear brake padsLefthand side worn the most?
Need to take careful notice of the correct assembly of the retaining clips, get it wrong, which is easily done, the clips can fall out.
D.08-12-21, 04:32 PM -
Reply to It lives: and EGR deletesI still follow Sharkcaver's adventures, I do not care what we drives, he gets into so interesting little known areas of WA.
Although his August trip was a bit too revealing.
WARNING images in the link may cause disturbance. Sharkcaver do...08-12-21, 02:06 PM -
Reply to Tyres and rimsHi Nell,
Welcome to the forum.
The NW standard size tyres are 265/65R17 or 265/60R18 depending on what model, so if you have 17" rims then 265/65R17 will be the size.
16" rims will not fit.
The most common size...08-12-21, 11:19 AM -
Reply to Progressive Rate Rear CoilsHi Ruari,
Glad it appears you got it sorted out and are happy with the results, they look good to me.
The real test will be when the loaded trailer is hitched up.
Great to see the supplier covered all your out of pocket...08-12-21, 09:00 AM -
It will also depend on how far rearwards the water tank centre is from the rear axle. 100 litres of water with a centred location of 1m behind the axle will have half the effect of the same 100 litres with a centred location 2 m behind the axle. The...08-12-21, 08:54 AM
-
Reply to Smart charger and lithium problemsTheir sales blurb about the Bluetooth monitoring indicates that you can monitor winching loads but the specifications state 300 amps for 5 seconds and 190amps continuous.
Interestingly they use the same blurb for all their batteries yet in the...08-12-21, 08:46 AM -
Hi Chris,
Since the photo has been taken from the ground looking directly up, and it appears between the rust stains we can see the bellhousing drain, unfortunately it looks like it could be a corroded welch plug or leaky drain plug. Looking...08-12-21, 07:05 AM -
Reply to Smart charger and lithium problemsI thought that it was only when you connected the negative side of the circuit directly to the negative terminal that you were bypass the current sensor.
What have people done when connection the negative when installing a winch, direct to the...08-12-21, 06:18 AM -
The Falken AT3W in a 265/65R18 114 is a standard load passenger construction tyre with an All Terrain tread pattern, whilst this tyre will give you extra grip off road the tyre is a light duty construction so you have a greater chance of ruining the...07-12-21, 08:03 PM
-
I think your Lovells MD rear coils will not be up to the task of a 180kg to 250kg ball weight when you take into account that for every kg of towball weight there is also just over half a kg of weight transferred off the front axle and onto the rear...07-12-21, 02:47 PM
-
Reply to Smart charger and lithium problemsAgree with Dicko, go back to DCS for their response.
The Mitsubishi smart alternator system is designed for a sealed lead acid battery and the smart charging is meant to save fuel and extend the life of the lead acid battery by not over...07-12-21, 12:30 PM -
Reply to 4M41 Hard Start - SCV?You can have an air leak in the fuel system and not have a visual fuel leak, because an air molecule is much smaller than a fuel molecule and the system is a suction supply design and not a pressure supply design.
OJ....07-12-21, 08:22 AM -
These online calculators are good for finding out and comparing the theoretical size of tyres but you then need to go to the manufacturers website to get the actual tyre diameter. As an example;
265/65/R18 has a theoretical diameter of 803mm...07-12-21, 08:19 AM -
Reply to Smart charger and lithium problemsWhat brand and model batteries are they?
Do they have an inbuilt BMS?
What is the temperature range for charging specified by the battery manufacturer?
OJ.06-12-21, 10:58 PM -
So lets quote the complete paragraph so it can be taken in context.
"Just because someone has a black, silver, blue or red 4wd, Ford, Toyota, Landrover, Isuzu or even any other different 4wd to what we chose to own, be it auto or manual...06-12-21, 07:38 PM -
I have not had a Pajero Sport rear air exit apart and there is very little info in either the parts or service manuals to determine how they are designed to operate.
In the PB Challenger and the Gen 4 Pajero there are rubber flaps that allow the...06-12-21, 10:30 AM -
Reply to 4M41 Hard Start - SCV?I am aware of one occasion that the hand pump seals had failed and this was causing the leak and not the filter bowl, hoses, connections or drain.
Vacuum air leaks are really hard to find and eliminated compared to pressurised air or fuel leaks....06-12-21, 10:18 AM -
It is the air outlet for the through ventilation system.
OJ.05-12-21, 10:32 PM -
On the PB/PC Challenger the maximum diameter tyre you can fit in the spare tyre area is 815mm and it is the width that is the first limiting factor.
The Pajero Sport is based on the Challenger floor pan so I suspect it has a similar limitation....05-12-21, 10:31 PM -
Reply to 4M41 Hard Start - SCV?Hi Toby,
The easiest way to see if you have an air leak in the fuel supply system, is after the engine has not been run overnight, push the hand pump on the top of the factory fuel filter. You should only be able to do 4 to 6 pumps before...04-12-21, 10:56 PM -
Suzuki Grand Vitara, max towing capacities varies between 1200kg and 2000kg.
https://www.carsguide.com.au/suzuki/...owing-capacity
Outlander, X-Trail, Forester, Sorento, Rav 4, etc all have towing capacities sub 2000kg.
...04-12-21, 04:34 PM -
Seriously???
The Suzuki Grand Vitara (no longer made) is a light duty 4wd/AWD, and more comparable to the Mitsubishi Outlander, Forester, RAV 4, X-Trail, etc. etc.
Yes these vehicle do make more sense to own around the city and suburbs...04-12-21, 01:09 PM -
Reply to 18 to 17 inch rims.You are correct Jason, some heavy duty 10 ply Light Truck Construction tyres like Mickey Thompson ATZ P3 & MTZ P3, Cooper ST Maxx & STT Pro are around the 809/811mm diameter but other brands such as Goodyear Duratrac and BF Goodrich are...03-12-21, 10:11 PM
-
Reply to 18 to 17 inch rims.Because the front and rear suspension is independent design, when you upgrade the suspension and get a "lift" all you are doing is changing the static ride height within the fixed suspension travel range, so there are no problems with clearance...03-12-21, 08:08 PM
-
Gen 3/4, Pajero Sport, PB PC Challenger and Triton all have a 3 piece steering columns.
All cars have some problems even the 4M40 series motor! EGR cooler, blocked intake manifolds, timing chain guide.
As for electronic driving aids these...03-12-21, 07:56 PM -
Reply to 18 to 17 inch rims.As long as they a genuine 17" Mitsubishi Pajero alloy rims with P46 offset then the fit. Some 17" genuine alloy rims off Tritons and Pajero Sports fit but you need to check the caliper clearance, these rims are offset P38 so the wheel track...03-12-21, 07:07 PM
-
Actually the Pajero Sport with its separate chassis and body construction, and its external dimensions are more similar to the original Gen 1 and also the Gen 2 Pajero's.
I can remember when the Gen 3 Pajero was released and there was many that...03-12-21, 08:55 AM -
Reply to Easy Up Touring Tent Options?All tents, swags, caravans, houses or any enclosed space where people are will suffer from condensation in the cooler climates. The average person loses about 200ml to 250ml whilst they are sleeping overnight and this moisture needs to go somewhere if...03-12-21, 08:43 AM
-
Reply to Tyre RecommendationIn general, most 4wd hire companies put on what every tyre is the cheapest and readily available, this is because the hirer is responsible for the cost of replacement for tyres if they are damage. Problem is when you hire a vehicle you can not see any...03-12-21, 06:58 AM
-
Hi Ron,
It could be a number of things causing the problem.
Do you have a complete list of the fault codes you can share, this will make the diagnostics much easier.
OJ.02-12-21, 06:28 PM -
Reply to Easy Up Touring Tent Options?We also have a rubber "holey" door mat that is placed on top of the C-Gear groundsheet, at the entrance of the tent and a small foldup stool so you can sit down to take off and put on your shoes/boots. It is a great assistance in keeping sand,...02-12-21, 09:27 AM
-
-
Reply to Aftermarket parts waitCOVID has severely disrupted the global supply chain and logistics, for all businesses.
I have overseas suppliers that cannot get the raw materials they need and when they need them.
Overseas manufacturers are also suffering from skilled...01-12-21, 11:18 AM -
Reply to Old viscount pop top winderHi Craka,
Have you considered contacting Goshen direct to find out who the AU agent is?
Have you determined which series system the pop-top is using?
https://goshenstamping.com/lift-system
https://goshenstamping.com/me...01-12-21, 10:57 AM -
Reply to Easy Up Touring Tent Options?When we brought our Black Wolf 240 we also invested in a C-Gear ground mesh ground sheet that not only covers the tent flor area but also the ground area of the verandah.
Not cheap, but Australian made and a great bit of gear.
https://ww...01-12-21, 10:55 AM -
Reply to Aftermarket parts waitAnd be double or triple the price!
Australian Made cost money that people do not want to spend!
OJ....30-11-21, 04:48 PM -
Cruisn06's Pajero has done 10's of thousands kms through Asia, Europe and Africa with his heavy roof load and many of those kms off made roads, and yes it is much more than Mitsubishi recommend. Obviously the setup and installation he has has past the...30-11-21, 03:17 PM
-
Reply to Easy Up Touring Tent Options?Hi Mark,
We went through the same issue almost 10 years ago, having had a large family tent for 20+ years.
I had a cheap 4 person "pop up" tent with a floor area of 2.4m x 2.4m with 1.9m standing room, it was light (12kg)...30-11-21, 11:11 AM -
Reply to gearbox troublesHi Shane,
With the information you now have, a good mechanic should be able to check and adjust the inhibit switch in less than 1/2 an hour if they have a hoist.
OJ.29-11-21, 06:24 PM -
Reply to Shocks or Shocks & SpringsHi Jimi,
Measurements for ride heights are what MMAL supplied when they registered to import the Pajero Sport in to Australia.
http://rvcs-prodweb.dot.gov.au/perl/...2016135344.cmd
So if we average...29-11-21, 05:26 PM -
Reply to Suspension recommendations please!Hi Tommy,
No problems with the help.
What part number coils did you end up fitting?
OJ.29-11-21, 03:06 PM -
Reply to Shocks or Shocks & SpringsHi Jimi,
Q1. What are your ride heights when measured from the centre of the wheel hub to the under side of the wheel arch when measured in a vertical line, PS must be parked on flat level ground or as nears as possible, measurements in...28-11-21, 09:40 PM -
Reply to gearbox troublesAdjustment for the Jatco VA5A Auto.
INHIBITOR SWITCH AND CONTROL CABLE ADJUSTMENT
AC606208AC00ENG.pdf AC606208AC00ENG.pdf
1.Move the selector lever to the N position.
2.Loosen the adjusting nut, and set the manual control...28-11-21, 09:30 AM -
Reply to Shocks or Shocks & SpringsHi Glasgerion,
Q1. Have you ant extra weight permanently over the front axle?
Bullbar, winch, 2nd battery, underbody guards or do you intent to fit any of these?
Q2. Doe you have any permanent extra weight over the rear...27-11-21, 05:35 PM -
Reply to gearbox troublesThe inhibit switch on the side of the auto gearbox, where the selector cable connects to the gearbox selector is most likely out of adjustment.
Is the gear box a VA5A or a V5AWF, need to know this because the adjustment procedures are slightly...27-11-21, 12:19 PM -
Reply to Please identify oil coolerBest way to check is put your VIN into a search on Partsouq, get the correct part number and then start searching that part number.
Even though the 4M4 series motor has been around for a long time it doesn't mean that all parts are interchangeable...27-11-21, 08:49 AM -
The Simpson is too big to fence and gate off and the SA Government/DEWNR simply do not have the financial resources for such a project.
There are already permit systems in place and quite a few regulations and the majority of these are good...27-11-21, 08:36 AM -
Reply to Suspension TravelAlso need to consider that with independent front and rear suspension design the diffs are fixed, so when you increase the suspension travel, particular in the downwards movement you increase the operating angle of the driveshaft joints.
These...27-11-21, 07:03 AM -
Reply to Electric Pajero!?My PB Challenger is 10 years old with 180,000kms on the odometer, has spent about a 1/3 of this off the bitumen, on trips it is heavy GVM+150kg, it has upgraded tyres and suspension and Auto Mate. It has been very reliable, capable on and off road, apart...26-11-21, 08:59 PM
-
Reply to Electric Pajero!?Could this be a Pajero Sport/ Pajero replacement?
Hybrid Ford Everest?
2022/23 release.
https://www.carexpert.com.au/car-new...lectrification
"We expect the plug-in...26-11-21, 07:54 PM -
Reply to Electric Pajero!?26-11-21, 06:51 PM
-
Well that is an interesting discovery!
It seems that the differences are related to the years and the market spec.
One is constant and I didn't know this, is that by selecting ASC OFF disables the engine power reduction function of...26-11-21, 06:54 AM -
Reply to Transmission change.Hi Jonas,
According to the Service Manual DTC 33 Fault Code is a Second Solenoid Valve System fault. If this fault code occurs the the gear dash display will flash "N" and the transmission will not change up past 3rd gear.
...25-11-21, 07:00 PM -
Reply to Passenger Side MirrorHi Dennis,
Put your VIN in PartSouq to get the correct part number, then do an online search of this part number online. This mirror was used on PB/PC Challengers as well as MN Tritons. Expect to pay between 1/3 and 2/3's of the MMAL price....25-11-21, 06:40 PM -
This does not surprise me.
The TC system will be looking at both the wheel speeds and steering angle, so if the steering is not straight a ahead, and the TC ECU does not know the front, rear diffs and centre diffs are locked then the TC ECU will...25-11-21, 06:32 PM -
The KYB Skorched 4 heavy duty range have a reputation for riding firmer that the OEM struts and shockers, but I have not heard the same about the Excel G range.
Rarely would someone fitting replacement struts and shockers swap out good serviceable...25-11-21, 04:48 PM -
From the Service Manual;
The Active Stability and Traction Control System (ASTC) is installed.- The Active Stability Control System controls four wheels brake force independently and also reduces engine power to manage spin or drift-out
25-11-21, 10:24 AM -
Below is info from the Falken USA website in regard to the Wildpeak AT3W as you can see these tyres are available in light duty passenger construction SL (standard load) 4 ply rating and also in heavy duty Light Truck LT construction 10 ply rating....24-11-21, 07:43 PM
-
Reply to king springsGen 3/4 Pajero's are very sensitive to coil selection.
A 2013 NW most likely will have 150,000+kms and the factory suspension would have sagged from the factory specifications of 503mm front and 533mm rear, What are your ride heights now?...24-11-21, 02:18 PM -
Reply to Switch off EGR for $1Ok, you have the delete resistor in series with the thermistor so you are still getting a a variable temperature signal to the ECU and this is the most likely cause of you problems.
The EGR will remain closed if the temperature signal is...24-11-21, 10:13 AM -
Reply to Switch off EGR for $1Hi Dennis,
How is the delete resistor wired into the circuit?
Is the delete resistor in series with the thermistor?
Is the delete resistor in parallel with the thermistor?
Is the delete resistor replacing the thermistor...24-11-21, 06:36 AM -
Reply to Passenger Side MirrorHi Dennis,
I have never had a mirror apart but work on the theory that it is an assembled unit so it must be abled to be disassembled. Problem is that there are often one way clip type fittings that unless you can work out how to unclip...24-11-21, 06:31 AM -
Hi Jason,
The Falken Wildpeak AT3W in 265/70R17 121S are a heavy duty light truck construction that are approved for rims from 7.0" to 8.5" so standard 7'5" Pajero rims are fine. Personally I would not use 7" wide rims...23-11-21, 11:02 PM -
23-11-21, 07:35 PM
-
Any hybrid HT/AT tyre will have good on road manners and a slight improvement in off road traction, if you want a slightly stronger tyre then a XL load index will be beneficial and if you want to go up a diameter.
Look at the following tyre that...23-11-21, 07:14 PM -
I wonder if there is some damage done to the front freewheeling actuator and it is not fully disengaging.
Have you tried selecting 4H and does the noise go away?
OJ.23-11-21, 06:37 PM -
Hi Redbruce,
Goodyear new tyre release?
Is this the Territory and the Trail Runner ranges, when are these being released in AU and in what sizes and load indexes?
OJ.23-11-21, 11:30 AM -
Reply to Intercooler swapThanks Pat, I will be interested to see what the results are when towing on a hot day.
OJ.23-11-21, 06:36 AM -
Reply to Oil leak above starter - 2009 NTX2 and torque the fittings correctly.
OJ....22-11-21, 08:41 PM -
17" or 18" rims?
Do you want standard diameter or go up a profile and gain 13ishh mm of ground clearance?
Manual or auto trans?
If Auto do you have a torque convertor lockup kit fitted?
O...22-11-21, 08:37 PM -
Reply to Intercooler swapHi Pat,
It is hard to tell from the photos but is the replacement intercooler larger?
You have seen a lowering of engine air inlet temperatures so something is providing this extra cooling effect.
Cost?
...22-11-21, 08:23 PM -
Reply to Better than D shackles.Wise advice from someone not interested in making a dollar from you.
Safety chains are meant to be short enough so the drawbar will not contact the ground in the event of the trailer decoupling or if the hitch receiver pin falls out and...22-11-21, 08:04 PM -
If you think it is tyre noise then could yo have bent something in the steering or suspension?
You may need to have the wheel alignment checked.
OJ.22-11-21, 07:37 PM -
Reply to Check engine lightThere is a known problem with certain batches of glow plugs across all Mitsubishi diesel engine vehicles.
Here is a link to a Service Bulletin that dates back to 2016 so it will be worth asking the Dealer Service Department on this problem....22-11-21, 03:51 PM -
Reply to Suspension recommendations please!I have run my PB Challenger for over 150,000kms with the slight harmonic resonance/vibration that occurs between 35kph and 45kph under acceleration, I have also had the dynamic mass balance removed from the diff for a similar amount of time, with no...22-11-21, 03:43 PM
-
Do not trust tyre resellers.
You need the tyre that suits your use the best, so have a careful think about what you need in a tyre vs what you want in a tyre.
If you choose a nice quite comfortable tyre HT passenger construction tyre...22-11-21, 03:32 PM -
Hi Lance,
The front suspension of Gen 3/4 Pajero's cannot be fitted with "inserts" to my knowledge, the complete strut must be replaced.
The coils can be reused if you are happy with the ride heights, comfort and body roll....22-11-21, 02:09 PM -
Hi Lance,
KYB do a Excel G range that is OEM standard.
Front Strut Part Number 341251 cost between $280 and $320 a pair online.
Rear Shockers Part Number 344300 cost between $180 to $200 a pair online.
Repco sell...21-11-21, 11:03 PM -
Reply to Better than D shackles.Over kill!
Have a look at this thread, I did a deep dive on the requirements after I had a trailer uncouple and tested the safety chains.
https://www.pajeroforum.com.au/forum...afety-chains-h...21-11-21, 05:34 PM
Leave a comment: