480 results in 0.0388 seconds.
-
-
There is a hotline fix to remedy this issue. If they dont play ball then contact MMAL customer care. But warranting an 11 year old vehicle is at MMAL discretion. It doesnt matter if it is a known problem. Not all Challengers areTtritons have this ...Leave a comment:
-
Mitsi dealers are required to record details of all Mods done to a vehicle and keep on file (record on the Repair order), and for anything that makes the car unroadworthy they should be advising the owner of this....Leave a comment:
-
yes thats itLeave a comment:
-
Somebody was making a cosy nest in thereLeave a comment:
-
Reuse, and no sealant at allLeave a comment:
-
All of the U codes you get in the engine ECU are communication codes caused by ECUs in the circuit sharing information, and not getting a response from systems the car does not have. It is a very early design of canbus which hadnt changed from its inception...Leave a comment:
-
Yes you can use it as a normal tailgate, but after playing with one, it is so handy to haveLeave a comment:
-
Foaming and excessive churn of the oil causing poor lubrication. Pressurisation of the axle does occur, But even with very high oil levels i have only ever seen 2 tritons leakingLeave a comment:
-
Yeah that is pretty low spec. We had similar in Low spec tritions a few years back.Leave a comment:
-
There should be a sticker on the inside with the manufacturer on it. MMAL used a few suppliers over the years, so there are at least 3 different canopies for MNLeave a comment:
-
Different countries have different audio units. post a pic and i see if i recognise itLeave a comment:
-
Remove the pipe that goes from the filter to the engine, and pump it through. you can use a plastic bag over the outlet so you dont dump fuel over the floor. When fuel flows out of the pipe freely, pop it back on, give the primer a pump and Robert...Leave a comment:
-
That black layer is paint, and it clogs up the tiny gaps in the pads and creates a terrible racket.
Any rotors i get to fit go on the brake lathe with a strip of emery cloth to clean that crap offLast edited by DibbyDibbyDJ; 11-03-22, 03:58 PM.Leave a comment:
-
I wouldnt touch the sensor. if you stress it or the connector ,it could fracture or just work loose over time.
If you need to crank the engine just remove the blue relay in the small relay box and power the starter from there.
...Leave a comment:
-
Reply to Owner Manual - 2021/22 QF PS1 week ago
-
Reply to 2011 PB airbag light just came onThere is a hotline fix to remedy this issue. If they dont play ball then contact MMAL customer care. But warranting an 11 year old vehicle is at MMAL discretion. It doesnt matter if it is a known problem. Not all Challengers areTtritons have this ...2 weeks ago
-
Reply to Modifications & Mitsubishi warrantyMitsi dealers are required to record details of all Mods done to a vehicle and keep on file (record on the Repair order), and for anything that makes the car unroadworthy they should be advising the owner of this....4 weeks ago
-
-
Reply to Dirtiest Cabin Air Filter Awards!Somebody was making a cosy nest in there01-04-22, 06:49 PM
-
-
Reply to Fault code U1100All of the U codes you get in the engine ECU are communication codes caused by ECUs in the circuit sharing information, and not getting a response from systems the car does not have. It is a very early design of canbus which hadnt changed from its inception...24-03-22, 07:30 AM
-
Yes you can use it as a normal tailgate, but after playing with one, it is so handy to have18-03-22, 05:40 PM
-
Foaming and excessive churn of the oil causing poor lubrication. Pressurisation of the axle does occur, But even with very high oil levels i have only ever seen 2 tritons leaking15-03-22, 07:01 AM
-
Reply to New member, new QE owner.Yeah that is pretty low spec. We had similar in Low spec tritions a few years back.13-03-22, 09:41 AM
-
Reply to MN Triton Canopy?There should be a sticker on the inside with the manufacturer on it. MMAL used a few suppliers over the years, so there are at least 3 different canopies for MN12-03-22, 08:23 PM
-
Reply to New member, new QE owner.Different countries have different audio units. post a pic and i see if i recognise it12-03-22, 06:29 PM
-
Reply to Filter serviceRemove the pipe that goes from the filter to the engine, and pump it through. you can use a plastic bag over the outlet so you dont dump fuel over the floor. When fuel flows out of the pipe freely, pop it back on, give the primer a pump and Robert...12-03-22, 06:26 PM
-
That black layer is paint, and it clogs up the tiny gaps in the pads and creates a terrible racket.
Any rotors i get to fit go on the brake lathe with a strip of emery cloth to clean that crap off11-03-22, 03:49 PM -
I wouldnt touch the sensor. if you stress it or the connector ,it could fracture or just work loose over time.
If you need to crank the engine just remove the blue relay in the small relay box and power the starter from there.
...21-02-22, 06:02 AM -
Castrol DEX3 works fine. it was the approved oil for a longtime...20-02-22, 10:02 AM
-
You do not need to run the engine. Just turning the steering left to right will pump out all the oil at a slower rate. Works very well. Have done it this way for years14-02-22, 06:14 AM
-
Reply to Dealer Vs local mechanicMaybe you have had a bad experience in the past. Who knows.
So while the apprentices are doing the work what do you think the time served, qualified experienced guys are doing?
Yes MM dealerships use apprentices. All workshops...10-02-22, 04:34 PM -
i havent changed single water pump in all my mitsi years (7). I have only seen one fail in that time and the shaft was bent by an a/c belt shredding and whipping off. but that needed a radiator too and cowling, fan etc...09-02-22, 08:24 PM
-
The Mitsubishi 5 litre plastic containers are no longer available. So we have to use Diaqueen sp3 now as that is all they supply. it comes in 4 litre tins, and a change is approximatly 3.5 litres if you just undo the sump plug.
i am pretty...09-02-22, 03:49 PM -
-
Reply to 2015 - 2019 Towbar wiring recall.Most of these have been done now. Sadly it only applies to dealer fitted MMAL towbars (because they didnt read the instructions).
If the bar was fitted outside the network it is not covered.08-02-22, 07:47 PM -
You use a bent piece of metal or a bent cable tie. the Manual states 8mm below the fill hole.
FWIW the workshop manuals state 2.6 litres, but this is wrong. MMAL workshop manuals are full of errors, thats why the info gets repeated again...08-02-22, 07:43 PM -
Reply to Rear diff magnetIts not unusual. If you are bothered show it to your dealer, but im sure they wont be worried. Probably more worried about what oil Ultratune put in your diff and did they overfill it....08-02-22, 04:03 PM
-
Correct amount in Challenger rear diff is important. The filler plug IS NOT a level plug. If you fill to the level of the plug you have put more than 2.1 litres in.07-02-22, 06:43 PM
-
Reply to 195km Service CostsLooks like they only charged you for front diff oil (1.15l) as the rear takes 1.6l
In my experience the techs are required to document exactly what oils and quantities are used on the repair order. And the twats in the office charge out...26-01-22, 03:51 PM -
Reply to Mitsubishi coolant??Aswell as the radiator drain plug, there is a plug on the bottom edge of the oil cooler for draining the block. When you drain this as well, and replenish the overflow bottle you get nearly 10 litres out.
Regarding changing to another type...25-01-22, 04:07 PM -
Reply to MMC dropping BT randomlyTry this.. When playing or using phone go into the control centre ( swipe down right top corner) and turn OFF bluetooth from that page ( press the bluetooth icon). Do not go in to settings and do it.
This can prevent the bluetooth stopping...24-01-22, 07:20 PM -
Reply to MMC dropping BT randomlyAre you running ios 15.1? They have bluetooth dropping out issues. 15.2 should have fixed that but i havent had a chance to check for myself.
Also if your HFM module version is lower than 19 there is an update available (hands free ...24-01-22, 04:08 PM -
Reply to ECU Re-SyncIt is not always possible, as the ECU will be coded to the ETACS immobiliser, and they need to have the same VIN in both. Some ECU's can be re written, but I have never tried to do it on a Paj.
i would try asking the dealer if they could...21-01-22, 09:02 PM -
Not sure what is mean by DPF clean, but the only time when a Regeneration only will fix a problem is when it is driven slowly around town. Its probable you have an air leak after the turbo and before the throttle, which is causing overfuelling and...18-01-22, 04:06 PM
-
Reply to Advice or help pleaseIn 2012 the LS and XLS has rear diff lock, whereas the basic 4wd did not. So if your car has paddle shifters for the auto, then you should also have Rear diff lock....08-01-22, 06:23 PM
-
Reply to Auto transmission weirdness.Are your reverse lights working?
With all those symptoms it is likely you have blown a fuse. Check all the fuses01-01-22, 08:24 PM -
Reply to DPF System Sevice RequiredOnce Regeneration is judged as necessary the ECU checks all parameters are in spec and starts to overfuel the engine. The Exhaust temp, Catalyst temp and DPF temp all start to rise. When it reaches the required DPF temp, then the PM starts to burn off....26-12-21, 12:34 PM
-
-
-
Reply to DPF System Sevice RequiredYou will not get the code to clear until you reset the oil level counter. The code will be P252F. Oil level high. It is not a level sensor, it is an added fuel counter.
The DPF will not regen until the counter has been reset and code has...21-12-21, 12:33 PM -
Reply to DPF System Sevice RequiredYou will not get the code to clear until you reset the oil level counter. The code will be P252F. DPF will not regen until counter reset and code has cleared and fault has been fixed. The days of clearing codes and she'll be alright mate wont work...21-12-21, 12:32 PM
-
Reply to DPF System Sevice Requiredthere is no point in replacing the oil until you have found the cause of the problem. All that will happen is you will wreck more oil as the burns fail.
there are 5 factors which decide if a Regeneration will occur.
1 Correct...20-12-21, 10:45 AM -
Reply to DPF System Sevice RequiredIs there a split in your intercooler cold hose? The one to the throttle body?19-12-21, 06:13 PM
-
Reply to DPF System Sevice RequiredWhy would you need a new DPF? And where does the 10k come into it?
Basics first.
Check your oil level. Is it high?...19-12-21, 10:46 AM -
Reply to Please identify oil coolerThe Element looks the same but the housing doesnt look right. The oil filter has a remote body bolted to the housing where this one is integral.
I think.......27-11-21, 07:37 AM -
Reply to Check engine lightthat one has been updated. it is just an addendum ( correction ) to rhe service manual.23-11-21, 06:57 AM
-
Reply to Check engine lightThats a new one to me. Will look it up in the manual tomorrow. Its not in the hotline fix or service bulletin database22-11-21, 06:10 PM
-
Reply to Driving in 4HYes that one. remove the bolt, bend the mount so it extends away and refit and try again....20-11-21, 07:44 PM
-
Reply to Driving in 4HDoes your NX have DPF?
Common cause of vibration on variants with DPF is from the front DPF mounting rubber contacting itself and causing NVH...20-11-21, 10:33 AM -
Its either use the link or do some groundwork yourself and contact the accessory manufacturer...15-11-21, 06:13 AM
-
Reply to Stuck EGR or Turbo - Help pleaseExactly. And even by a few mm at the wrong revs the engine will run rough and smoke
That is what I do to confirm it...14-11-21, 06:55 PM -
Reply to Stuck EGR or Turbo - Help pleaseI have edited my original reply. The scoring will not be on the motor, but on the valve shaft part of the EGR....14-11-21, 06:37 PM
-
14-11-21, 01:14 PM
-
Reply to Stuck EGR or Turbo - Help pleaseOn pajero, overboost is controlled by EGR, and in my experience most Paj (and Triton) intermittant boost losses are caused by EGR sticking.
If the mechanical slide sticks open on an EGR, then the motor will return to its rest position, leaving...14-11-21, 10:11 AM -
Reply to Stuck EGR or Turbo - Help pleaseSticking EGR valve. Thats why it was lumpy idle and sooty exhaust. Turbo would not cause issues at idle. Remove EGR, strip off the motor and look for scoring on the shaft as you open it by hand. Cleaning it might help, but if there is bad scoring you...14-11-21, 08:33 AM
-
Reply to Engine fault lightYou need to read the fault code in the ECU and post it here. This will give you and us a big clue as to why the light is coming on10-11-21, 03:50 PM
-
If you can get hold of a good bi directional scantool you can activate a fuel pressure leak test. This ramps up the fuel pressure to test the sealing of the injector pipes. This would pinpoint the exact pipe that is leaking giving you the choice of either...09-11-21, 06:09 AM
-
Yep, that will give you enough clearance to wiggle it out. The pickup hangs down a little, but there is enough room.07-11-21, 09:02 AM
-
You dont have to REMOVE the diff, just drop the mounts and let it hang down. Then the sump will come out07-11-21, 07:32 AM
-
Reply to Service interval.No, That service guy is talking BS. I think they forgot to reset it and tried to fob you off. There is no extended service for low kms, in fact low kms is severe usage and means more frequent servicing....04-11-21, 08:29 PM
-
Okazaki has been a MMC plant since 1977 where recently they have built the previous generation of Outlanders and the Eclipse cross.
...
02-11-21, 04:24 PM -
Reply to 2019 outlander thoughtsSteer clear of the diesel, unless you plan on doing a lot of kms. DPF, EGR and cracked manifolds, as well as noisy balance shaft assemblies.
2.4 petrol is a good runner, but not sporty or gutsy in any sense. CVT is ok as long as its had...01-11-21, 04:54 PM -
Does it say your phone is supported?26-10-21, 07:12 AM
-
23-10-21, 08:40 AM
-
So from your settings page you have various tabs at the top ie: information - Bluetooth - Phone function..
further along is one called system and on the bottom left is a button RESET ALL Hit this, and the system will factory restore,...21-10-21, 09:43 PM -
Do you have QE or QF?...21-10-21, 05:19 PM
-
Reply to Removing Headlight PajSportThere are a couple of bolts hidden under the bar at the side, they go through the big plastic clip that secure the bar on the top side edge. If you are careful you can peel the bar away, but its safer to remove it entirely20-10-21, 07:52 PM
-
Reply to Diesel Injectorsafter fitting and coding an injector the EML stays flashing until a relearn has been completed. So if your EML is off it has had a relearn16-10-21, 03:00 PM
-
Go in to you menu and find the system tab that has a reset button on the bottom left. This will factory reset the SDA so you will need to update time and retune your radio stations and re-pair your bluetooth devices.16-10-21, 12:58 PM
-
Reply to 60,000 service costBut if you have a good relationship with your dealer.....
they cannot change the fixed pricing at all, so would have to charge you and MMAL for doing it, But do it at next service for instance. There is a bit of trust on both sides.
...12-10-21, 06:12 PM -
Reply to 60,000 service costA good dealer will do the full service as specified. A better one might offer to leave the valves until nearer the actual kms.11-10-21, 10:03 PM
-
Are your reverse lights working? If not its possibly a blown fuse11-10-21, 04:26 PM
-
Reply to NX control arm bushesWas there movement, or are they just looking for work?...11-10-21, 11:04 AM
-
Reply to transmission drain plug pajero sportTo just change the oil once would take 30 mins probably, if it had to be done again due to not clean enough, maybe another 20 on top of that. This depends on their hourly rate08-10-21, 09:36 PM
-
Reply to transmission drain plug pajero sportThere is not a filter. It is a strainer, that is why it is not a scheduled replacement.
If the strainer has fragments in it, then changing it is going to do no good, your trans is already shot.
The workshop procedure states...06-10-21, 07:23 PM -
Reply to MAF SensorYeah why? They rarely go wrong. I have replaced 2 in 7 years, and they were both non genuine ones that were giving incorrect readings to the ECU....06-10-21, 04:01 PM
-
Reply to DPF Burn IndicatorA PID (Parameter IDentifier) is an item of data that the ECU sends to an OBD reader. Just as the throttle position sensor, Air flow sensor and fuel pressure sensor (as examples) are all PIDs, so is the DPF regeneration Flag. So with a suitable program,...05-10-21, 05:06 PM
-
Reply to DPF Burn IndicatorThere is a PID ( Parameter IDentity) for DPF regeneration on NX models.05-10-21, 02:52 PM
-
Reply to transmission drain plug pajero sportSame procedure as on the sport. 40-45 degrees, just dripping from level plug....04-10-21, 08:12 PM
-
Reply to transmission drain plug pajero sport5mm allen key to remove plug. This is the level plug. Then put allen key back up inside hole and unscrew drain insert.Oil will then drain.
It is not supposed to be tight, so when refitting just a light tightening.04-10-21, 01:44 PM -
Reply to Pajero NS transmission service oil?http://www.datateck.com.au/lube/castr_au/
Says NS Paj is Transmax Multivehicle ( which is SP3) for AT
And specifically DEX 3 for PAS01-10-21, 09:58 PM -
Reply to Pajero NS transmission service oil?It it has the Dipstick then it is the Jatco, and will use SP3 oil. Other companies make compatible oils so you dont need to buy from MM.
Dexron 6 is compatible, and i have a Mazda that uses it, so I use SP3 in that as i get it cheap01-10-21, 10:54 AM -
-
Reply to small injection quantity learningBetter to let the fuel to get up to temperature than to fool the ECU. The SQL outcome is dependent on fuel temperature....17-09-21, 08:31 AM
-
That sticker is for the tongue as you correctly stated. There should be a similar sticker on the towbar ,if it is genuine15-09-21, 06:25 PM
-
The alternator nuts dont normally come loose, unless they were not tightened enough previously03-09-21, 08:14 AM
-
Just read a different thread about key confirmation buzzer, and recalled a few Mitsis suffering with door locking not working, caused by the car thinking the key was still in the ignition. This was caused by the microswitch on the ignition lock sticking,...30-08-21, 09:29 AM
-
77nm is the correct torque figure for these bolts. And put an extra washer under the passenger side rearmost bolt that goes up into the chassis rail. The bolt is too long, and bottoms out on the inside of the rail before the fixing is tight enough....22-08-21, 08:35 PM
-
Reply to Exhaust Smell in cabinPS and MQ/MR Triton have all experienced this fault. I Have seen no repeat failures as yet....21-08-21, 11:04 AM
-
Reply to Exhaust Smell in cabinStopping at lights and in light traffic will pause the process, and if for long enough will stop that regen, Next time the conditions are right it will start again....21-08-21, 10:21 AM
-
Reply to Exhaust Smell in cabinVehicle needs to travelling at at least 40kmh for regen to take place. Travelling slower than this causes regen to fail, and ultimately DPF warning light to come on20-08-21, 09:36 PM
-
Reply to Exhaust Smell in cabinYep, every service includes an inspection of the exhaust system, which includes manifolds and DPF operation...19-08-21, 06:43 PM
-
Reply to Exhaust Smell in cabin62nm on the manifold bolts to head, similar for turbo to manifold and DPF to turbo. The heat sheild mounting plate can crack with the expansion, right near the rearmost bolt. Not a concern for a self repair though.
I have done a few...19-08-21, 06:42 PM -
Reply to Exhaust Smell in cabinIf you are going to attempt this yourself i would suggest going for a fast drive beforehand, to get the exhaust nice and hot, then remove the covers over the turbo straight away and undo the 3 fixings that hold the DPF to the turbo. They can be stubborn...19-08-21, 08:20 AM
-
Good result, Was it from a NX?...14-08-21, 02:47 PM
-
Check your door pin switch screws are not loose. this is a common cause of intermittant locking issues....14-08-21, 10:54 AM
-
Better to tell them the caller is hearing an echo on the line. That is the actual fault that prompts the update, and MMAL warranty do not have a software update for screen freeze, so the dealer may only do a factory reset...14-08-21, 09:37 AM
-
Reply to Black dust/soot outside of the EGRif it is near the vent hole for the diaphragm then it is leaking and will need fixing (replacing)13-08-21, 10:42 PM
-
Reply to Rear spring upgrade - ConfusionThat would be the cause of the occasional TWANG, when lowering vehicle of the hoist with aftermarket springs then....11-08-21, 07:43 PM
-
Reply to Exhaust Smell in cabinAny accessories bolted to the front? Non MM bullbar? Extra lights? Winch?
All these things cause poor airflow through the engine bay, and if during a burn you shut off the engine, underbonnet temperatures, which are already higher, due to...11-08-21, 07:40 PM -
If you get one from another NX then its a simple 5 minute job. Other versions will fit, and all plugs will go in, but some functions will not be active, due to vehicle coding.07-08-21, 07:08 PM
-
Yeah, its gone and pooped itself. Not a very common concern, I have only seen 2 other do it. Hopefully you are still in warranty.
Refer to dealer for a replacement unit07-08-21, 03:13 PM -
Ok, from your description i thought it was an SDA (smartphone display audio) , but after seeing your picture it appears you want to fit a MMCS.
So forget what i said about bluetooth module.
You will have to research wiring diagrams...02-08-21, 08:01 AM -
If you have an external bluetooth module, then this will not be used with a SDA, as it has the Bluetooth built in. Same goes for GPS
As for wiring diagrams try..
http://mmc-manuals.ru01-08-21, 10:21 PM -
Reply to Electric park brakeThey are similar in size but i fail to remember if they are the same. The Rotors are similar, but not interchangable
A fully locked wheel would cause a dramatic reaction, much quicker than blown tyre, but the system should...31-07-21, 04:56 PM -
Reply to Electric park brakeThis procedure above is used when the actuator has been replaced.
I have never MANUALLY had to release the parking brake. On every occasion i would use a MUT or similar to activate FULL RELEASE CONTROL. Which is much simpler, and i would...31-07-21, 11:45 AM -
Reply to Electric park brakeI have not heard of this happening, however there is a concern over fragments of shoe material coming away from the shoe, causing jamming.
So even with the warning light on, when EPB operation is impossible, if the material comes away, a...31-07-21, 11:33 AM -
There are no accessories that need the unused plugs for any feeds or returns, so best advice would be to not use anything like that incase something does pop. Some of the circuits they are connected to may already have a near limit current draw on...22-07-21, 08:13 PM
-
The one on the right of the steering wheel? After removing the lower plastic panel above your feet ( 4 clips) you undo one screw at the bottom and use a plastic trim tool to prise it away at the top and it will all unclip21-07-21, 09:37 PM
-
Try pushing the plug further on as you press the catch in, then pull back21-07-21, 09:31 PM
-
Reply to Electric park brakeYes
Yes
Yes
No
Very possibly, When you Apply as an emergency brake it WILL stop the car unlike any handbrake i have tried. But the ECU knows you are moving therefore you must want emergency stop rather than normal parking bra...16-07-21, 08:05 AM -
Reply to Electric park brakeThe chunks missing from the leading edges are quite common. They can get inbetween the shoe and drum and leave a mark. I had a warning light on one earlier this week, and I did a clean and readjust and erased the code and it was all ok.
...15-07-21, 08:21 PM -
Reply to Dash PlugNo. It will not be connected to a component. It may have supply and earth connections15-07-21, 08:12 AM
-
Reply to Water in fuel lightthin long nosed pliers to squeeze the back of the clip together and it pops out...14-07-21, 06:15 PM
-
Radiator drain only lets out about 5 litres, but undoing the engine drain on the oil cooler housing lets the rest out of the motor, and it isnt that hard to get to.
The workshop manual doesnt mention draining for rear heater, It only gives...12-07-21, 08:37 PM -
Reply to Transmission filler/ dip stick?On flat level ground undo the 24mm plug on the front. It shoulld just be at that level, so it just drips out slowly, or if you use a cable tie to stick in the hole it should just get wet if you put in in horizontally..
if it pours out it...12-07-21, 08:03 AM -
Reply to Transmission filler/ dip stick?Dont undo trans plug..Trans has got to be at 40 -45 degrees C and on dead flat ground or preferably a hoist. Fluid should be red anyway, or black if it has been abused. Could it be from front diff? Thats yellowish?
Show us a pic if you...11-07-21, 10:51 PM -
Reply to Transmission filler/ dip stick?No It is the same plug as the drain. But it doesnt actually drain until you remove the insert in the hole after you have removed the plug...11-07-21, 08:47 PM
-
Reply to Transmission filler/ dip stick?No dipstick on the sport. Checking is done with gearbox at certain temp, on flat surface and by removing the level plug, which is the same as the drain plug...
What colour is your oil leak?11-07-21, 05:35 PM -
Reply to Electric park brakeThe actuator is well protected and lives under the drivers floor. The concern is with large amounts of foreign matter getting inside the rear brake shoes and seizing them up, which overstresses the actuator causing the code. The actuator being faulty...11-07-21, 11:26 AM
-
Reply to Come on Mitsubishi.Its an NT, so well out of warranty unless you are the owner of a golden ticket 10yr drivetrain warranty. The biggest hurdle to overcome will be parts cost and availability. The transfer case in itself is a dream to strip and rebuild. But if there are...08-07-21, 08:30 PM
-
Reply to Is my valve clearance done by ear?those washers are reused. The ones that are changed are on the injectors, sadly not in these pictures...08-07-21, 08:17 AM
-
Reply to Is my valve clearance done by ear?When you bought the car you were signed up on the free servicing plan. This was agreed at purchase, and the sales dept have no input after then....07-07-21, 07:26 PM
-
-
Reply to Factory or third party towbarTSA is part of the vehicle. It is a program built in to the vehicles systems (ASC, SRS, PCM & ETACS) as part of the MiTEC System...04-07-21, 08:33 AM
-
Reply to Factory or third party towbarOnly if fitted before delivery of vehicle...03-07-21, 08:20 PM
-
Reply to Factory or third party towbarTrailer Stability Assist is only available with genuine accessory towbar.03-07-21, 05:21 PM
-
Reply to 60,000 service costThe price is $699 because the valves do get adjusted, and not the audible check. If anybody believes their valves were not done at service bring it up with the dealer. If they didnt do them they are not just defrauding you, but MMAL aswell...30-06-21, 07:55 PM
-
Reply to 60,000 service costThe only reason the services are cheaper with CPS is that MMAL pay for the balance of the service cost...29-06-21, 07:42 PM
-
All the ones i have done have been inside Std warranty...29-06-21, 07:36 PM
-
The original notification details the fault on NT Pajero.. Nothing since heard about a cause or a production fix....29-06-21, 05:54 PM
-
It is the cooler itself that fails...27-06-21, 10:10 AM
-
There is a spare connector for accessories by the battery that feeds into just by the passengers kick panel. The towbar uses 1 of 4 pins, so there are 3 remaining. you could use these for BV supply, but an ignition switched feed is not available without...26-06-21, 10:12 AM
-
Just completed a 17 NX this week. Parts had been on order for over 6 weeks.
Owner relieved to get his car back, but enjoyed the Paj Sport he was loaned...26-06-21, 09:41 AM -
Reply to 60,000 service costInlets are always tight on these engines, Exhausts are on the loose side.
Check if ultra tune know the procedures for tightening the injectors, and what seals MUST be replaced to ensure warranty before you hand them the keys.
...25-06-21, 06:21 PM -
Reply to EVC iDriveI recently drove a Paj Sport in ECO mode. Gearchanges were poor and snatchy. Not impressed really24-06-21, 05:58 PM
-
Do you have any other Genuine MM accessories fitted? Towbar? Brake controller? Extra lights?24-06-21, 08:06 AM
-
12v accessory socket wiring.
Read my signature23-06-21, 08:03 AM -
Reply to Brakes vibratingNot something i have heard of as a known concern.
Yes, brake rotors can overheat and warp, but not through normal use, and TBH it is much harder on a Paj to do this than most other marques i have worked on....22-06-21, 08:26 AM -
D419 Pin 1 is fused by 7.5 amp fuse 7, pin 2 by 10 amp fuse 18,pin 3 by 7.5 amp fuse 8. It is a spare connnector that has no purpose in our market
But these fuses are used by other circuits, so be careful using feeds and earths from this...22-06-21, 08:08 AM -
Reply to Disabling airbags off roadThere is no simple way to disable the system. Even if you unplugged a side airbag to put the warning light on, the system is still active and can go off if required.
And in an off road impact you would still benefit from SRS17-06-21, 06:10 PM -
Reply to Balance arm?Those pictures are not the same as Australian versions, as the Pajero sport in Australia has coils on the rear, not leaf springs14-06-21, 01:27 PM
-
Reply to Buying advice pleaseThe fully corrected engine blocks came out in November 2019, since this date there have been no repeat failures on ones to my dealership. All MY's of MN and PB/C 4x4 are affected and can fail with out warning...13-06-21, 12:24 PM
-
All of the bolts that secure the manifold to the head (10) are the same length. Then there are 2 or 3 (depending on manifold type) that hold the upper inlet to the manifold. There are 2 bolts that hold the fuel rail to the manifold. 2 Bolts hold the...09-06-21, 08:16 AM
-
Its a known issue with Mitsibushi technical, so there have been a few cases. I have only seen two do it so far. Refer back to ARB as per above09-06-21, 08:07 AM
-
Reply to Hylomar alternativeThe non Genuine ones from Bursons are fine. On older vehicles we use them all the time to keep costs down.08-06-21, 08:01 AM
-
Reply to Push to StartAdding a push button to the original wiring MAY work, but the Immobiliser system needs to see specific signals to ensure operation. As you go from ignition on to crank with the key, the ECU recognises what is happening and gets ignition on signal from...07-06-21, 06:23 PM
-
Reply to Hylomar alternativeIts probable the covers are not as straight as they should be, due to being over tightened at some point. The torque setting is quite low for these bolts, and is rarely observed IMHO. Adding sealant will probably do very little if this what has happened....06-06-21, 10:54 AM
-
Reply to time to move on or not??The only way to really tell if the lines are any good is when you torque them up. If as you are tightening you can feel them get tighter, just before wrench clicks, then they are ok. If they just click all of a sudden then the material that forms the...03-06-21, 08:38 PM
-
Reply to ASX dieselIt is a proper auto in the diesel, not a CVT.
They do have some faults. Exhaust manifolds love to crack, and vent gases into the engine bay and up in to the heater intake. And the balance shaft drive assembly gets noisy, confirmed by a...26-05-21, 08:14 AM -
When using a smoke machine i disconnect from the intake throttle body and plug it shut, then from the turbo end i use an adapter to plug that end, then introduce smoke ( or pressure in your case) through that adapter.13-05-21, 07:50 PM
-
you need to plug one end to allow the system to pressurise, but dont use too much pressure. You could damage the intercooler or the seals.13-05-21, 07:18 PM
-
Yep 100% you need a smoke machine, 5 mins to find the leak rather than spend time looking around guessing and removing things to check.
But the common things on yours are split intake hose that goes to throttle body. And if the intercooler...12-05-21, 06:01 PM -
Exactly right, you used the words i use when I get asked about the strainer.
Any bits in the strainer will be the least of your worries...10-05-21, 06:31 PM -
Seeing as it exceeds and replaces Dex III you could do a PAS flush , that will use a litre or so
...
09-05-21, 04:12 PM -
.
Should be if its accurate
40 is the optimum temp, its what i aim for, but 45 is the limit. Over that and you must cool it down before restarting...08-05-21, 08:39 PM -
...
<WHEN THE M.U.T.-III IS NOT USED> 08-05-21, 08:27 PM -
Reply to Changing the Diesel FilterLook at the front of your filter housing, there are some arrows that line up with a mark to confirm filter is tight enough.
Unscrew the plastic ring holding the 2 parts of the filter together and pull the top off carefully. Remove old filter...05-05-21, 06:10 PM -
Reply to EGR deleteIt would be interesting to see some engine data from a Thai Vehicle, just to see DPF operating parameters. That kind of soot build up even overtakes 3.2 pajero in severity (sorry guys)...04-05-21, 08:49 PM
-
Reply to EGR deleteI would love to see that picture
Maybe the fuel in your country is bad and that is the cause, but rather than spend money on different gadgets to alleviate the symptom why not get MMTh to fix the root of the problem....04-05-21, 06:12 PM -
Reply to EGR deleteUnder normal operating conditions the 4N15 does not suffer with carbon build up inside the manifold. So if yours is then there is something wrong which you need to get checked out. Especially with only 10000 kms on it04-05-21, 08:06 AM
-
Reply to EGR deleteIf your Pajero Sport has the 4N15 engine then there is not need for EGR defeat . If it is a 4D56 then a EGR delete cable can have advantages, but physical blocking of the EGR is not advised due to the fact of the EGR is used to control boost. This happens...02-05-21, 09:10 PM
-
-
I just keep flushing until it comes totally clear, then flush the other way, and more will come out. Undo the block drain plug and radiator drain again, and more will come out.
With it being your own car you can run it with water and flushing...28-04-21, 08:15 AM -
Yes it does, so a oil change or more is required. I always remove the filter and wash it out with fresh oil as part of the first change, then another change, and if ok, another oil change with a new filter.
For the cooling system i remove...27-04-21, 10:38 PM -
Were you charged the full price for the service?...24-04-21, 10:36 PM
-
Reply to Challenger PB new engine?Genuine new engine at main dealer..... 12 to 15 K23-04-21, 08:04 AM
-
Yes i agree. Should be fitted clean and dry with no sealer. If sealer is needed, it is because they F***** it up....21-04-21, 01:50 PM
-
-
First time will probably be poor assembly at factory ( either not locating o'ring correctly or not even fitting it)..
Subsequent times will be down to Overightening of the bolts. They have a low torque setting, and overtightening pulls...21-04-21, 08:04 AM -
Larger brakes on the Pajero sport need larger wheels to clear calipers. This is why the 16's are not suitable19-04-21, 07:47 PM
-
Reply to Police Spot ChecksOn a car with ASC, a wider track really screws up the computers inputs, and therefore the outputs.
But on all cars it changes the basic principles of the steering and suspension, hence why (in VIC) 25mm is the maximum you are allowed to...18-04-21, 01:19 PM -
The kind of air leak to be concerned about would be either a split in the rubber intercooler hose to the Throttlebody or around the pipe flanges that bolt on to the intercooler ( noticable amount of oil mist around the joint). Both of these are very...18-04-21, 12:17 PM
-
it shouldnt be sluggish.
As for getting a refund? From Mitsubishi? Not a chance...
Your repairer should have found a fault causing the carbon build up. Of course the build up would cause sluggish running, but what caused the...17-04-21, 01:54 PM -
What symptoms are you having?...17-04-21, 12:54 PM
-
To be that bad at 67000 there is something else wrong going on. 4N15 do not carbon up like that. There will be another factor involved. Probably it has an air leak after the MAF or a sticking EGR valve shaft.
EDIT : And at 67000 it would...17-04-21, 09:38 AM -
Reply to DPF Fail towing in the outback :(Copied from Owners manual.
"lUse engine oil conforming to the following classification:• ACEA classification:“For service C1, C2, C3 or C4”• JASO classification:“For service DL-1”
Dealers should be using DiaQueen DL-1 which is...16-04-21, 10:02 PM -
Reply to DPF Fail towing in the outback :(Ask the dealer what your average speed during regeneration is?
Has your engine oil level increased?
The heat under the feet is the DPF getting hot trying to/doing a regen
In your owners handbook it will tell you...13-04-21, 08:24 AM -
-
Reply to Fitting MM towbar to QFUnless you remove the bumper you wont be able to connect the wiring harness fully. There is a small plug behind the bumper you need to swap a wire out of.
Also you need to drill a 30mm hole in the lower 1/4 panel. Impossible with bumper...11-04-21, 11:06 PM -
Reply to 60000 km serviceAt 60000 they wouldnt pull the injectors out... unless you have a Pajero sport???
And if you do have a sport, the tarry build up is quite normal, and they should be cleaning that off as part of the service when they refit the injectors....07-04-21, 07:06 PM -
Reply to Blowing excessive black smokeOr if they used a scope to test it would take less than an hour. I only use diagnostics to test injectors, not removal and checking....02-04-21, 05:55 PM
-
Reply to Blowing excessive black smokeThe Female connectors do wear loose, an easy fix for that is to bend the pins on the MAF from a - - - - - to more of a / / / / /, but by not as much, in reality its only a tiny twist to ensure good contact. If all of the known fixes on here fail,...02-04-21, 09:26 AM
-
Reply to iCarSoft P252FThe code wont be preventing the burn. It is there because the burn cannot occur, so the ECU puts more fuel into engine to get temps up, but fails, and oil gets diluted. Once it reaches 1550cc it trips that code, which you are correct, can be erased via...29-03-21, 06:09 PM
-
Reply to Removing the Intro Screen Messagedo you still have to press i agree or does it just show and go on its own...07-03-21, 08:28 PM
-
You can use a small amount of engine oil on the fuel pipe when inserting that into the small seal to make inserting easy, but i have never put oil on the oil seal before putting it in. They can pop out, around the injector body, hence the superglue....07-03-21, 07:21 PM
-
Reply to Removing the Intro Screen Message2.2.0006.0200 is the latest firmware available07-03-21, 11:18 AM
-
A few drops of superglue around the large seals before Drifting them home stops them popping out. Nothing needed on the smaller seals.
No lube on them either. Make sure injector contact surfaces are clean and dry before refitting07-03-21, 08:04 AM -
Reply to Multimeter CapabilitiesThe 10 amp rating is obviously for checking current draw, and you are correct in saying 10amps is the norm. From my cheap $30 one i use at home to my Fluke 88 i use at work they are the same piddly 10 amps, which when checking for current draw, in reality...06-02-21, 02:26 PM
-
Reply to Entertainment unit freezingHave you cleaned the screen with a cleaner? Majority of unresponsive screens are down to contaminants on the surface...02-02-21, 03:58 PM
-
Reply to Free Plugs in DashboardThese plugs will be for Higher spec versions of your car, or versions in other countries that have different equipment. There may be voltages or earths on some, but likely only power for illuminating switches.01-02-21, 06:31 AM
-
Reply to Entertainment unit freezingNo software available yet, but is for release very soon. Send me a PM and i will keep you updated
....31-01-21, 03:20 PM -
Reply to Clock spring?Seeing as it is the same clock spring for your airbag wiring, i would suggest the genuine path would be the best route.30-01-21, 07:21 PM
-
Reply to upgrading exhaust on NX dpf modelsSeeing as the DPF is under the vehicle and can reach temperatures of at least 750 degrees c, then the risk of parking on grass is real....30-01-21, 07:51 AM
-
Reply to Manual Idle Speed ControlExcept the Accelerator pedal circuit has 2 parts, Main and Sub, to co-relate the data to the ECU. Best to leave that one alone.
Maybe a small brick on the pedal?21-01-21, 04:17 PM -
Reply to second key not workingIt needs programming to the immobiliser. Simple thing for Mitsi dealer to take care of.....21-01-21, 04:12 PM
-
Reply to Service Cost $2500??? Is this right?Never personally seen that yet, however I have heard that issues will occur. I know i wont be putting SP3 anywhere near mine...16-01-21, 03:30 PM
-
Reply to Service Cost $2500??? Is this right?Yep the Aisin suffers with that too. Recently had a Pajsport that had penrite SP3 equivalent added instead of ATF-MA1. Started giving large shift shocks on gearchanges.
Personally would never disconnect a transpipe to aid flushing, not...16-01-21, 11:42 AM -
Reply to Automatic transmission filter typeThe V at the beginning denotes Drive type. V is 4wd, R is Rwd. The 4 or 5 or 6 or 8 refers to the amount of ratios available14-01-21, 06:29 AM
-
Reply to Head unit replacement problems?Like i said in the other thread you have posted this query in. You Have blown a fuse... It may be for another circuit. possibly trans or reverse lights. Do reverse lights work?12-01-21, 04:03 PM
-
-
Reply to Service Cost $2500??? Is this right?An easy way to tell if they are still ok, is when torquing them to the correct tightness, they will be easy to tighten and as you start increasing the torque you will feel a gradual increase in resistance. This is the material reforming to the injector...11-01-21, 06:35 PM
-
Reply to Sudden Auto Transmission IssueYou have blown a fuse. Check your reverse lights, are they working?11-01-21, 06:26 PM
-
Reply to "SRS / Airbag light"You are correct DDJ, MMAL is ultimately responsible and the dealer service department are the stuck in the middle between an unhappy customer and the MMAL.
I know some dealer service departments push back on warranty claims because they do not...08-01-21, 09:29 PM -
Reply to "SRS / Airbag light"Goodwill is "code" for an out of warranty repair that the manufacturer is covering the cost for. What are they supposed to call it? Make up a random word?
Goodwill is also used to replace the majority of Triton engines that have...08-01-21, 04:05 PM -
Reply to Electric park brakeSince PS release i have seen about 7 with failures.
3 of which were down to workmanship issues, as in rear rotors being fitted outside of the dealer network, and not following handbrake adjustment procedure correctly.
2 were...08-01-21, 06:05 AM -
That is a tough one to swallow, especially as you say it runs so good.. and ultimately it is up to you whether you do or dont, so I'll just give you some background info.
I have never had to check a set at 20000, so i cant say for sure...05-01-21, 06:27 AM -
Reply to Pedal sinkRear brake lines can be problematic to bleed on Triton. What year and model is yours?04-01-21, 05:20 PM
-
Reply to Injection Quantity LearningThe engine speed will rise up, in about 4 different stages. Stage one starts off, then will go through the 4 cylinders, then settle. Then stage 2 goes off, higher rpm.... when it starts do not touch throttle or steering, it will stop it, and it may or...02-01-21, 07:49 PM
-
Reply to Injection Quantity LearningThere is no way to adjust idle speed.
Regarding Small quantity injection learning, this can be done by vehicle without intervention from scan tool if all parameters are correct.
1. Engine coolant temp 85 or higher
...02-01-21, 02:58 PM -
it is not the camera that does the sensing. It is your parking sensors. They are sensing the towbar.
Check your owners manual if they are factory fitted. In there may be instructions on how to change to towbar mode. Alternatively remove...26-12-20, 11:45 AM -
Good chance then that something there is causing your problem25-12-20, 08:43 PM
-
I see in your signature you use EGR delete. How have you acheived this? I ask because a sticky egr valve can cause low boost pressure, in fact the ECU controls EGR operation to reduce overboost.
i have a small sliver of tin i slide in by...25-12-20, 06:13 PM -
Reply to WipersCut down a 6mm wide insert and disassemble the rear arm with a flat blade screwdriver to fit. Only takes a minute07-12-20, 07:38 PM
-
-
The only difference you will see are that the "nag" screen no longer needs pressing, and some typos have been corrected. All of the other software changes are operational, as in to do with how the systems operate04-12-20, 03:59 PM
-
-
Reply to Changing ML Triton serpentine beltIts not that bad. Just make a note of belt route, slacken tensioner, slip off pulleys and wind it around the fan.30-11-20, 05:50 PM
-
Reply to BrakesIts Hygroscopic. It absorbs moisture from air.
Easiest and most effective way for one person to bleed brakes on a Pajero is to open the nipple and let the fluid just run through. No need to pump, no need need to use pressure or vacuum bleeder,...26-11-20, 06:06 AM -
Reply to catch cans and warrantyYep i agree.
I have seen a badly fitted catch can that was piped wrong, and when draining the oil from the sump it came out in trickle until oil cap was removed. I had never seen that before...25-11-20, 11:58 AM -
Reply to catch cans and warrantyIn the engine ECU data is an item called CVN. This is a factory set item for the ECU program, and changes once a remap has been carried out. If it was a MMAL update, the number still changes, but if aftermarket it changes to a unknown variable. dealer...25-11-20, 11:56 AM
-
Reply to Battery Drain IssuePossibly anecdotal, Possibly relevent...
2014 Paj comes in for service and intermittant flat battery (original one still fitted)
Diagnosed as faulty battery, customer declines, on price.
RACV attend and fit Calcium...24-11-20, 01:57 PM -
-
Removal and cleaning is the only way to go. You dont want all that carbon going into your cylinders and possibly getting stuck on a valve seat, gumming up a ring, blocking your cat or DPF.18-11-20, 06:01 AM
-
Reply to 2020 NX Pajero brake disc faultPajero handbrake is operated by shoes inside the rotor. So that sounds like BS coming from your dealer. That mark is probably caused by the pads, like i said in previous post, it is visible on a lot of cars. But if you have shudder through wheels and...10-11-20, 06:08 AM
-
Reply to 2020 NX Pajero brake disc faultIs it a crack? Or is it just the mark from where the car war parked recently? This is quite a common occurance09-11-20, 06:06 AM
-
P0299 can be when manifold is blocked, but check those sensor hoses thoroughly, I had one last week with code and asking for manifold clean. Being an early model, the pipe goes in to the lower cover not the top inlet, and the lower pipe had a nice split...05-11-20, 06:07 AM
-
Reply to Dual Battery Pajero SportARB do a kit for mounting underneath between transfer case and fuel tank. Neat looking, but some of the installations has been very average.03-11-20, 06:30 PM
-
I had a look at a data list today and saw "Lock up solenoid' with a duty % cycle reading.
I haven't heard of the term "flex lockup" so i wonder if this is the same thing. Im driving a Nov18 build first thing...29-10-20, 08:41 PM -
Is there a PID associated with this i coud look for? that may have been deleted?
I may not get to drive these models, but if i can quickly plug in and get some info i will....29-10-20, 07:13 AM -
I have seen one badly choked NS requesting it at 80km intervals. Unfortuanatly the customer had just bought the car and was returning it to seller, so we never got to see an outcome, or get much more data from it...29-10-20, 07:09 AM
-
A regen should only take a maximum of approx 10 minutes to complete. The easy way to tell if it is trying to do one would be to use a scan tool to read the parameter.28-10-20, 08:47 AM
-
Reply to DPF HealthIn the engine management data list are 2 items which refer to next regeneration required in kms. The items are numbered 193 and 196 and are named "Regeneration start distance"
An engine that is working ok will have these distances...26-10-20, 06:45 PM -
Reply to Service resetWhen the dealer does the indicator reset, if your schedule is out slightly you need to do a “extra reminder” setting. Once you have done this, the dash button press will not work again until the “extra reminder” has been cancelled....24-10-20, 09:25 AM
-
Using a jet wash you WILL only get a low flow through the DPF. The first time I washed one wash unsure if it was ok. But that is fine. But a very small trickle would perhaps mean a blockage. I have always washed out DPFs with success, but have never...23-10-20, 11:12 AM
-
Reply to EGR valve noiseYes, the ecu drives the egr valve motor to its limits to ensure the potentiometer is working and the egr valve is in the closed position for starting.21-10-20, 05:15 PM
-
Reply to Steel Rims Pajero MY17Try your local dealers, some do wheel swaps and have a few sets of steelies laying around21-10-20, 07:08 AM
-
As usual OJ is bang on the money with 15nm, Overtightening is a big problem. The standard bolts are no good on an impact driver and the threads stretch. Then when you unwind they strip out the captive nuts. Better bolts just move the problem on to the...20-10-20, 07:28 AM
-
Rear shoes badly (incorrect procedure) adjusted.
Exhaust manifolds cracking due to poor airflow
Oil leaks by fuel pump or timing case area
Seat trims rubbing against plastic surround on drivers seat and splitting leather
Coolant...19-10-20, 05:13 PM -
Whoops. yep will not work on NS...09-10-20, 05:10 PM
-
Engine Temp 85c
AT temp 60c
fuel temp 45c
No accessories or heater or lights on, steering wheel straight. Dual battery disconnected. I-drive and EGR defeat devices also cause issues.
If it doesnt...08-10-20, 05:15 PM -
Reply to NX Windscreen WashersThere will be a build up of mould in your washer bottle. Only way to remedy is to remove the bottle,thoroughly clean and flush out pipes and probably fit new jets. No point just fitting new jets, they will clog again.
Washer bottle...29-09-20, 07:05 PM -
-
Reply to NL Takata Airbag AlertCongratulations guys
Just heard that all dealers have received an email today explaining that air bags are now available for Australian vehicles covered by the NADI airbag recall
28-09-20, 10:58 AM -
The outer driveshaft hub nuts. The nuts may be tight, but the shaft may not be fully seated correctly.
Best practice is to remove the wheel and the centre hub nut. Then grab the shaft and try to move it in and out. If not free, then use...27-09-20, 02:15 PM -
No dash loosening required at all.
Half a dozen screws and a couple of nuts holding glovebox surround on and nuts securing the inflator....27-09-20, 02:10 PM -
Reply to Essential mods new diesel ownerDealers should have no problem with catch cans and extra fuel filters being fitted.
Some will not be interested in the maintainance of them though, so dont expect them to drain catch cans or replace your extra element.
...24-09-20, 08:16 PM -
Reply to Did my valve clearances today.Put them in clean and dry, with some supaglue for lube only.18-09-20, 05:50 PM
-
Reply to Service gouging?It is listed for changing at every service
https://www.mitsubishi-motors.com.au...nance-schedule
If you are not on Capped price servicing, then ask for it not to be done when booking in...18-09-20, 05:46 PM -
-
Reply to Manifold cleanWhen you get a quote for cleaning, it might be worth getting a quote for new manifold....14-09-20, 04:43 PM
-
Reply to Manifold cleanNever bothered changing the gaskets on 4D56. Never had a problem, and done this many many times.
On Pajero you can’t reuse manifold to head gasket , or the copper washers on fuel return pipe, but again, the metal ones are ok to reuse...14-09-20, 04:37 PM -
Reply to Manifold cleanThere are a few crevices inside the manifold where the carbon collects. You won’t be able to get a brush to remove it. Just be sure there are no loose bits before the manifold goes back on.
Cleaning of the ports in the rocker cover...12-09-20, 10:15 PM -
Reply to NX Nudge BarThere are 2 8mm holes that have to be enlarged to 14 or 16 mm. No big worry12-09-20, 10:09 PM
-
If if was gonna move it would with a spanner. I have tried drilling and retapping.
But time is other people’s money, so grind and weld on new nut is quickest....12-09-20, 07:57 PM -
Reply to NX Nudge BarOn the factory bar, you just need to drill out some plastic holes on the grille support.12-09-20, 07:52 PM
-
Yep. so many do tow with bolt in and tight. Cutting off the welded nut and putting a new one is easiest way..... If you have a mig12-09-20, 06:27 PM
-
The bolts purpose is to stop The towbar tongue rattling when not towing. You are supposed to loosen it to allow movement when towing and then Retighten when finished.12-09-20, 02:32 PM
-
Is the wheel facing the ground or boot floor? Should be boot floor11-09-20, 03:24 PM
-
They do have receivers, but not built in software for navi.
Might be a better option to upgrade the head unit for one that has the functions you require. The SDA IMHO has proved quite fragile in regards to homebrew software,...07-09-20, 12:46 PM -
You have a large ipad type screen with 3 touch buttons on each side?07-09-20, 12:34 PM
-
Do you mean SDA? MMCS did not have android auto capability.
If you did mean SDA, then there would be no advantage to having exceed firmware as the exceed or any other SDA have Navi software built in.
And by writing incorrect...06-09-20, 10:46 PM -
Reply to Reasonable tyre balance weights?In Vic, more than 85g per wheel is unroadworthy. I have seen some with much more than this. Bad fitting is main reason although some cheaper brands are a struggle. That’s where a good fitter will go the extra mile to ensure compliance. But I do...04-09-20, 08:01 PM
-
Reply to 4WD Supercentre.I bought my EDS from them one evening, but before the order was even processed, I got an email from them advertising it at same price with free shipping. I had paid $10 shipping on my order.
By the time i got through to them...02-09-20, 01:04 PM -
Reply to Swapped ECU and now it won't go.Is there an ECU above the passengers feet on left side? This is the engine ecu.26-08-20, 09:33 AM
-
Reply to Traction controlGo for a drive in a straight line. Will reset steering angle sensor25-08-20, 09:19 PM
-
Reply to 60000km Service NX PajeroWho told you that?
Coolant and brake fluid MUST be done at intervals specified. If the dealer doesn’t, then you should go back to them and complain....25-08-20, 12:04 PM -
Reply to Proper brake bleeding procedureI have 2 clear bottles with rubber hoses attached to the top. I start with emptying the reservoir as much as possible, Then refill with fresh fluid.
Then starting with the rear, i put my 2 bottles on the rear calipers and open the bleed...24-08-20, 11:06 AM -
Reply to System ErrorThe screen is looking for the head unit it was originally connected too. That’s why you are getting the error message21-08-20, 08:50 PM
-
Reply to NP 3.2 won’t stay running!!Sounds like immobilised.
What exactly was the immobiliser code?20-08-20, 07:56 PM -
Thats encouraging.
A point missed from OP was that even if ACC is affected, normal cruise control will still work.18-08-20, 10:44 AM -
-
Reply to Steering reachOP mentioned replacing the boss on the wheel. This would not be covered by the certification by the manufacturer.
It seems you just want to disagree with every point.
So i have given my informed advice....15-08-20, 11:33 AM -
Reply to Steering reachMy original response to the OP, from Victoria, stands. With regards to Roadworthiness VSI 8 section 13.4 regarding steering wheels states
"Vehicles manufactured after June 1995, which are required to comply with...15-08-20, 10:45 AM -
Reply to Trailer Plug ProblemYes but not as standard from supplying dealer, you had to get auto elec to rewire, or ask dealer to ensure it is done.
Again, depending on the van supplier. A 3 way fridge will run off 240v,...14-08-20, 06:27 PM -
Reply to Steering reachAir bags are designed to go off and already start deflating as the driver hits the bag. They are designed to operate within an envelope of operation, and having the wheel too close will cause the driver to possible hit the bag before deflation starts,...14-08-20, 06:15 PM
-
Reply to Trailer Plug ProblemYou sound surprised your fridge didnt work. Did you ask for it to be wired for that function? There is no provision on a Genuine towbar kit for fridge wiring, nor is there a recognised Standard as to how you would connect a fridge. Some need larger...14-08-20, 03:48 PM
-
Reply to Steering reachMoving the steering wheel closer by any other means than factory fitted reach adjustment would change airbag deployment area and therefore make vehicle unroadworthy and ADR non compliant.
Not advised14-08-20, 11:42 AM -
Reply to NX - Hands Free problemThere is a software update for handsfree issues. If your software version is or below 2.0.xxxx.xxxx, then the update is available so refer to your dealer.14-08-20, 10:41 AM
-
Reply to Trailer Plug ProblemThe black wire? Is an accessory wire, but not connected to anything. you can run your own wire to this pin, but you would need to know current load on the circuit first, so you dont fry your ETACS...13-08-20, 09:53 PM
-
If you have a towbar (factory type) the connections are down in the left front kickpanel side trim. these wires need to be secured using the cable ties and foam padding supplied in the kit otherwise they vibrate. Same applies to wiring by the jack as...11-08-20, 10:43 AM
-
-
I have knocked so many off i now just automatically remove it. makes life easier not having to search for it.
09-08-20, 02:30 PM
-
looks about right. i usually spray a tiny bit of white spirtit on the rubber then slide it on.09-08-20, 01:30 PM
-
Reply to 2010 ASX Diesel coolant change/flushIts so much work to remove that plug. How i do it is do drain radiator, refill with water and flush with a hose.
Run engine for a couple of minutes to circulate
Then drain radiator again, leave plug open...09-08-20, 12:12 PM -
Reply to Catch can/EGR deleteAny kind of EGR delete or defeat modification is illegal.
A catch can should be No.1 on your list08-08-20, 02:18 PM -
Reply to EGR deleteThe 4N15 has it sorted. I have seen many 120000+ motors with no blockages.
EGR delete on this model would be a waste of time...04-08-20, 05:31 PM -
-
Reply to EGR deleteCatch can is a good idea. But where have you heard of Pajero sport having intake issues?...04-08-20, 08:16 AM
-
Reply to MQ Airbag Light Resettry cycling the ignition a couple of times. The code will stay as stored, but if inactive the light will go out02-08-20, 10:35 PM
-
Reply to Mitsubishi UK/ Europe closes28-07-20, 10:30 PM
-
Reply to Triton MR Driving lightsThey fall out. The little legs shake loose. Just terrible.22-07-20, 10:31 PM
-
Reply to Triton MR Driving lightsplease nobody use these....
They are terrible and a huge cause of breakdowns as they fall out or connectors come loose.
Mitsubishi fuses always cover more circuits than the diagrams say, and22-07-20, 09:19 PM -
Reply to Triton MR Driving lightsNot aware of one above drivers right foot on MN or PB
There is a 4 pin plug up above front passengers feet on left side that goes to battery. if you have factory towbar one of the wires gets used. This is on all models except...22-07-20, 09:16 PM -
Reply to Triton MR Driving lightsClipped onto the left headlamp lower part is the connector with 8 or 10 wires in it. One of those is your headlamp feed.
Most accessory kits come with a bulb adaptor, that plugs in to the harness to the bulb. Unless you have HID of...22-07-20, 06:57 PM -
Reply to 60000 km serviceWill ultra tune do the service to spec though? I recently had an Outlander come in with DPF blocked with 88000 on the odo. Local garage did the 90000 at 85000.
They didnt do the valve clearances, or replace the fuel or air...22-07-20, 05:25 PM -
Reply to Burning oil smell?Check your oil level. If it is way above the max mark close to or past the X then its likely aDPF issue. If its near normal or low its something else20-07-20, 07:55 AM
-
Just reuse the steel gasket that is already there. They are quite resilient.15-07-20, 07:32 PM
-
From that diagram and my memory that gasket isnt available. If it was it would be exploded view and there would be an N next to it denoting mandatory replacement. And the view does not show the bolts either, nor the torque figure.14-07-20, 09:33 PM
-
Reply to QE/QF ComparisonThose features are the same on QF as on QE. The audio unit is larger with QF. Im not sure if car play functionality is the same, with regards to Navigation apps. I have not had the opportunity to (car)play yet.14-07-20, 07:59 AM
-
-
Reply to QF Exceed tow barThe Redarc trailer brake kit is an optional accessory. Its pretty much plug and play, just need to swap some wires around under the footwell and add one under the bonnet13-07-20, 08:59 PM
-
Reply to Prematurely? Changing Oil & FilterIf you choose to do your own servicing thats fine. You cant update your service indicator without a bi directional scan tool, and you probably want to get your scheduled servicing done at a dealer anyway.
The only other things they...04-07-20, 04:03 PM -
Reply to Diff drain plug replacementCant remember on Pajero. I know Tritons are 10mm hex drain plug.
A lot of drain plugs on Mitsis are this type, with 24mm hex filler plugs. Outlander, ASX , Lancer.
Cant see it being a big deal...01-07-20, 08:00 PM -
Reply to DPF - What do I need to know?Some trucks do have A regen button. I know that my old 2011 Hino for instance had one, as im sure others do. My experience with it was if you dont do it in time, as was the case with mine, as i didnt always have time to do it there and then, if i left...30-06-20, 08:26 PM
-
Reply to DPF - What do I need to know?As i have posted in other threads, the DPF system on the NX appears to reasonably trouble free, with no issues coming through my workshop.
The only problems i have seen have been EGR cooler valves leaking soot by the vacuum...30-06-20, 08:16 PM -
Traction control light may come on after battery disconnect as the car forgets the straight ahead wheel position. Normally goes of after 2-300 metres in a straight line29-06-20, 11:09 PM
-
Reply to Engine doesn't accelerateI think everyone on here KNOWS of the legalities of defeating the EGR or DPF systems.
I am interested in the research regarding Turbocharger failure. Links please?29-06-20, 08:11 AM -
I would advise against anyone updating their own software. I have seen 2 self updated units with "unusual" software ID numbers being rejected for warranty repair after having an issue.
If the dealer bricks it, warranty cover...28-06-20, 04:18 PM -
Reply to QF Exceed tow barGenuine ones do if you leave the tongue in. But you can set rear sensors to towbar mode, which changes the detection area28-06-20, 01:11 PM
-
Reply to QF Exceed tow barGenuine QF towbar now fits BEHIND the rear bar and is concealed. FINALLY :-)
Anothe big advantage with genuine Towbars and wiring is Trailer assist. This will sense your trailer starting to weave and will control fuelling or individual...28-06-20, 11:09 AM -
Reply to Unknown VibrationYep, I was chasing a noise on an ASX, which i was adamant it was the exhaust heat sheild rattling. By pure chance as it was doing it i touched the windscreen, and the noise changed.
Removed the e-tag, Noise gone. Crazy what the smallest...15-06-20, 08:00 AM -
Reply to Accessories Position OptionsIf you leave it in neutral or in a gear as you turn it off it goes back to accessory.
As good as it gets14-06-20, 10:15 PM -
Reply to Nx Brake Bleed Procedure???????I have found on some Mitsi models that using vacuum bleed causes more trouble than its worth.
As for opening nipple when pushing back? Personally never bothered doing that,just being gentle with the pushing has always worked....13-06-20, 02:18 PM -
Reply to QF Snorkel OptionsThe joins between the snorkel and the airbox are pushfit only, with a foam seal. They are above the maximum wading depth of the vehicle, which remains unchanged, like you state, but as they are located above the wheel there is still a chance of ingesting...12-06-20, 08:12 PM
-
-
Reply to Injector solenoid oil leakAs a DIY fix, just replace the seal. Lucky as it is no1 its the easiest to do, Clean the area first, unclip the injector plug, carefully remove the seal. Dry the seal contact surfaces thoroughly, and slide new seal over injector. A few drops of superglue...03-06-20, 08:03 AM
-
Reply to Glow plug accessCheck your current draw when preheating. Will tell you if plugs are working02-06-20, 11:06 PM
-
Reply to AmpTo be honest you would get better sound with upgraded speakers and a non mitsi amp. And as the Mitsi system is run through the CAN network, and upgrades or additions to that are impossible without rewriting all the ECU on the network to recognise the...31-05-20, 01:06 PM
-
-
Reply to Drive shaft lubeThe UJ nipples should be greased at every service, the sliding one needs probably only 1 pump every service, and a little more after removing the shaft.30-05-20, 01:49 PM
-
Fuel pipes need to be torqued to 32nm, as the seat is designed to form to the shape of the injector. Any tighter than that and you will squish the pipe too much leaving them unable to squish anymore next time they are tightened. That is why they are...26-05-20, 08:17 AM
-
Reply to Disc machining tolerances.26.4mm is service limit on fronts. If it is 1mm above that i would say they are ok for machining.
The rears are thinner, but have a huge offset, and when machining these you can get a resonance or ringing sound, especially...21-05-20, 08:16 PM -
Reply to No bluetooth conection.Can you check that the tablet still connects?
Not all android os units have all the same functions available. Unconnected to your problem, but We are having issues with Android auto at the moment, with people buying new phones and...12-05-20, 05:32 PM -
Reply to Paint Brake caliperIn VIC it is unroadworthy, as the callipers may have damage that is being masked by paint, or could hide damage. Also may change cooling characteristics of callipers.
It is one of those
rules. I have never heard of a problem,...
01-05-20, 07:06 PM -
Reply to Paint Brake caliperjust be aware in some states painting callipers makes vehicle unroadworthy.01-05-20, 12:11 PM
-
Reply to Fitting inlet manifold gasketNot a problem on some models, but i have had to remove the pipe on occasion. The gasket wont come off the studs with it in the way. Same for refitting.
You must have the manifold bolts with the springs and cups..01-05-20, 12:09 PM -
Reply to workshop manualDealers cannot supply manuals as such anymore, they are on the MUT, However if someone asks us for pages, and know exactly what they want, we are more than happy to print some off, within reason, of course. If you ask for 50 pages, you might get short...27-04-20, 08:23 PM
-
Reply to Structual FailureThe biggest concern i see is DC utes with longer trays than specified. And the the common overloading with tools and equipment leads to problems later in life (of course its a warranty issue
) as well as handling issues with front end being...
25-04-20, 09:24 PM -
Reply to tools for removing tow bar boltsThe bolts shouldnt be that tight. If its a factory towbar ( as it says in your signature ) they should only be tightened to 77nm. The reason dealers shouldnt (and we dont )use a impact driver to tighten them is that the bolts could be damaged by excessive...25-04-20, 09:18 PM
-
I can guarantee that has NEVER happened in my place of work....22-04-20, 09:17 PM
-
-
Reply to Drive Line NoiseSounds like loose rear driveshaft nuts to me. Remove rear wheels, and centre grease cap. Loosen nut, Spray the hell out of the splines with wd 40, move the shaft in and out as far as you can9only a few mm) and keep spraying. When it moves freely refit...15-04-20, 08:36 PM
-
Reply to Welcome to my nightmare!Do you actually have the chip in the transponder? What type of key do you have? Picture of key would help
What happened to get to this situation?14-04-20, 08:18 AM -
Reply to 1992 nl - remove mongoose m80 wiringAll you can do is trace where the alarm harness goes to and fix the wiring back to spec. Normally where a circuit is cut, both the wires are in the same proximity, so it makes it easier. Fuel pump relay would be an easy one to use. It it time consuming,...13-04-20, 12:41 PM
-
Reply to Fog light switchSo if you have a switch you must have had foglights at some time. Find the wiring behind the front grille and connect to there. Relay should still be in circuit12-04-20, 10:44 PM
-
Always worth a try. When MMAL know of an issue like this you would be surprised at what they will pay for. If you are original owner that can help, but not necessary....12-04-20, 10:54 AM
-
You have a faulty ETACS unit. If in warranty no problem, if outside get your dealer to put in goodwill claim.
It is a known issue. When they replace the ETACS is is also possible they need to replace both transponders to ensure operation.11-04-20, 11:07 PM -
-
Reply to Serpentine Belt.Like i said "As far as i know". Ive worked at Mitsubishi in Aus for 6 years and have never seen one.
EDIT: Of course there are loads for sale on carsales.com.au. LOL
But I DO know that QE Paj Sport 4x2...03-04-20, 10:21 PM -
Reply to Serpentine Belt.I know RWD Triton MN is certainly lower power. RWD Challenger may be same, But AFAIK were not ADR compliant, like Pajero Sport RWD, so were not brought here.03-04-20, 08:04 PM
-
Reply to Serpentine Belt.The RWD version has a low power version 4D56. I'm unaware of what is different regarding the pulleys though.31-03-20, 06:28 PM
-
.... is coming soon. All Mits dealers here in Straya are getting the new software to talk to the new vehicle. I am sure we all know that is going to be a Renault. Lets hope the Renault CLIP software is more reliable than their vehicles.30-03-20, 10:19 AM
-
Reply to donor engine2wd is lower power, so not suitable. Has smaller turbo and higher compression ratio.
Auto or manual, they are the same, so no problems there.
As for finding a good HP motor? If you get one with engine number CZZ...29-03-20, 01:53 PM -
An other way is to do a SMALL INJECTION QUANTITY LEARNING as during this the pressure ramps up to maximum at the end.28-03-20, 08:17 AM
-
-
Reply to Information on DPF of an NXMY 17 Started Apr 1 2016
MY21 starts apr 1 202022-03-20, 10:17 PM -
Reply to "SRS / Airbag light"No, if fault happens and goes straight away fault is stored and light stays on. It is designed that way. We normally read codes and wiggle connectors and recheck if fault disappears, so we can show customer its correct.
It isn t hard...22-03-20, 04:43 PM -
Reply to "SRS / Airbag light"It will be an intermittant code. They can stay active, but very rarely. And the connection issue will be at the SRS-ECU plug. The pins will be slightly smaller than the sockets.
Was the light out when you got the car back...22-03-20, 03:19 PM -
For idling that is spot on. Some bi directional scan tools can do a fuel leak test to test the pipe connections, and also the return lines internally. This program ramps up the fuel pressure to maximum to allow you to look for leaks externally, and also...22-03-20, 09:11 AM
-
Reply to Information on DPF of an NXLook under bonnet, If it has DPF you will have a second EGR valve fitted here
https://imgur.com/YqX8nvI...21-03-20, 11:35 AM -
Reply to Information on DPF of an NXDPF on some vehicles (toyotas) have been troublesome, and people think they strangle the engines performance. On a well designed system, like your PS, they are trouble free, but 2007 pajero had one and not much was known about them outside of Dealerland,...21-03-20, 09:51 AM
-
Reply to "SRS / Airbag light"A quick wiggle of the ecu connector can cause a temporary fix. Real problem is that the pins are too small for the sockets, and these dodgy connections after years of accumalating moisture occasionally flog out.
It should be a warranty...19-03-20, 09:13 PM -
Reply to Fault codes/ SRS warning lightI think the code you refer to is B1610. This is a well known code due to connection issues in the harnesses. It is becoming rarer as most of the offending vehicle would of had the replacement by know. How far out of warranty are you? this was always...19-03-20, 07:02 PM
-
You are correct in its position, and in the fact that it will have some forward vision, but the problem arises that if SOME forward signal is transmitted, then not ALL of what is expected will return. That is what the calibration ensures.
...15-03-20, 07:07 PM -
I meant was the oil actually oil or was it diesel leaking?
What year is it? DPF model?...15-03-20, 09:31 AM -
Had a recent service? Has the oil seal around the injector popped out? That would explain oil. Or if it is Diesel, maybe the pipe is loose or fractured, caused by securing bolt loose? And a loose egr valve or pipe could cause that noise.14-03-20, 07:46 PM
-
Reply to MQ/MR Triton 2015-2019 RecallExactly. Supposedly about 5 have played up so just in case they recalled everything....12-03-20, 08:46 PM
-
Reply to MQ/MR Triton 2015-2019 RecallYep, all down to bad fitting. Mainly at one dealer who were farming out New car prep to outsiders, who didnt read the fitting instructions.12-03-20, 07:35 PM
-
Reply to Munji EGR Cable ExperiencesBut in reality, they dont suffer with this the same as the older designs. Yes, there have been problems with DPF regeneration and sensors, but these have been Assembly issues rather that design flaws.
I have seen totally clogged DPF,...08-03-20, 10:50 AM -
Reply to Central locking RPM sensingYou could get a RV Fridge relay that senses movement, and have that trigger door locking motors08-03-20, 10:23 AM
-
Reply to Munji EGR Cable ExperiencesNever seen a Pajero Sport Or MQ with a crudded up manifold. Pajero or ML always are...07-03-20, 05:43 PM
-
Reply to Coolant boiling on engine shutdownIt should still be in that side tank. A big consideration would be to check, once all leaks have been repaired, is trapped air in the system. I have seen many mechanics induce air locks in to tritons after fitting new engines for this over heating problem....07-03-20, 01:43 PM
-
Reply to Coolant boiling on engine shutdownNot a good idea to mix coolants based on their colour as a rule. Mitsubishi coolant is premixed to specification, and you mix it with another "green" coolant that is not premixed or mixed to another spec you are weakening or concentrating...06-03-20, 01:11 PM
-
Reply to Wow - The cost of Pajero Brake PadsOk. that will teach me not to read post correctly. Pajero Sport 2013?? Will not have EHB. It is obviously a Challenger. my bad
06-03-20, 12:33 PM -
Reply to Wow - The cost of Pajero Brake PadsMaybe they have them in South Africa, but they do not have them In Australia or Asia...06-03-20, 09:07 AM
-
Reply to Wow - The cost of Pajero Brake PadsThe only issue you would come across is if you adjust the handbrake shoes for any reason, say if you needed to machine the rotors and wanted to de adjust before removing them. There is a procedure for doing this. If you just turn the wheel a few clicks...06-03-20, 09:02 AM
-
-
Reply to Diesel fuelling mistake preventionThe Solo Diesel one used to be stocked by mitsi dealers, and we fitted them to our loan cars and staff cars. never had a problem with them, and easy to use.01-03-20, 03:57 PM
-
The best way without drilling holes is to use the accessory harness built in to the car. Behind the left front kick panel is a connector like this.https://imgur.com/abjFaat
The lowest #5 in the pic is the connector. If you have a...28-02-20, 03:55 PM -
-
Reply to NL Takata Airbag Alertit really depends on what was available at the time of build. if NADI had a shortage back then, they may have sourced inflators from Takata, or Autoliv, or numerous other suppliers....24-02-20, 07:14 PM
-
Reply to NL Takata Airbag Alertit is just the inflator that is faulty. the steel casing around the inflator is what fractures and injurs/kills you.
Nearly all of these recalls are inflator only. the only one where the complete airbag is replaced was CH Lancer...24-02-20, 06:58 PM -
Reply to Alternator getting hot.For some strange reason i thought you had a 2010, but then i re read thread. i will look at 2005 tomorrow.
This is 2010 diagram. https://imgur.com/nHOMMSL How many wires going in to your plug?24-02-20, 06:51 PM -
Reply to NL Takata Airbag Alert24-02-20, 06:08 AM
-
-
Reply to MmcsNo software updates available. If your HFM (handsfree) version is 19.00 then that is up to date as well. Mapping update is at 2019 currently...23-02-20, 04:49 PM
-
Reply to Transmission Oil CoolersDid they refit the factory air deflectors after fitting bar? Not having these fitted can lose you a few important degrees...23-02-20, 08:34 AM
-
Reply to Alternator getting hot.i would have to check wiring diagram to 100% sure, but you may have regenerative charging on that model. When You lift off throttle and ECU knows car is travelling at speed the alternator CAN output more power to the battery. Whilst the engine is on...22-02-20, 02:50 PM
-
Reply to NL Takata Airbag AlertThere is no mechanical reason why you cant do that. Except that the government would have to allow all the owners to ignore the ADR.
And we all know what A******* they are. There are lots of manufacturers in the same boat.
...21-02-20, 08:03 PM -
-
Reply to Alternator getting hot.Thats correct. With the main cable off there is no output as alternator is self excited, and as soon as it sees 12v at that terminal it starts charging. i have seen over 70v at that output terminal with a high resistance cable.20-02-20, 11:49 AM
-
Reply to Alternator getting hot.With alternator connnected,and engine running, try connecting voltmeter between output of alternator and battery positive.
This will check the integrity of the battery cable.
Less than 0.3 volts is acceptable. If it is higher...20-02-20, 06:41 AM -
Reply to NL Takata Airbag AlertSo yes, like I said the dealer does not have access to that info. You would need to contact MMAL directly...19-02-20, 06:15 PM
-
Reply to NL Takata Airbag AlertOnly if you have the VIN of the vehicle that they came from. That is the only identifier the dealer has....19-02-20, 03:18 PM
-
-
Reply to NX - Hands Free problemWhat audio unit do you have?
EDIT: Just read your other post. I gather you have an SDA. The handsfree is built into the SDA, the microphone is separate. What issue are you having?13-02-20, 07:52 PM -
Reply to Snorkel Install QuestionNot sure what brand snorkel you are fitting but be aware of wring harness that runs along the inside of the guard06-02-20, 03:57 PM
-
Reply to EGR quote $700 to replaceEGR oil seal? its only exhaust gas going through it. Cant imagine what they are on about.04-02-20, 04:29 PM
-
Reply to Manifold cleanYou would need the manifold gasket and the gasket between the manifold and the intake pipe.
If you loosen the fuel return pipe you will need the copper washers for that too.
Probably worth getting just in case.
The gasket behind...03-02-20, 06:23 PM -
-
Reply to REDARC towproThe harness is available separately , it is very easy to install with no messing around with diodes, running long lengths of wire or drilling holes or poking wires through grommets....01-02-20, 08:09 PM
-
Reply to Dpf deleteWhat do you hope to gain?
The DPF system on QE is quite robust and operates well unlike the pajero system...01-02-20, 07:14 PM -
Reply to Towing ECU fitting Rear AirconNever had to use it. is it mentioned in instructions?25-01-20, 12:14 PM
-
Reply to Towing ECU fitting Rear Airconif its the genuine ecu it is small enough to fit inbetween the rear panel of the car and the fan assembly. no removal of fan required.
that is the plug you connect the harness to24-01-20, 06:04 PM -
Yes same engine as MQ. It does take less time than MN Or Pajero to do, and coupled with every 60000kms interval works out cheaper....23-01-20, 05:11 PM
-
it is easy , but the procedure for refitting is important, and sadly not always adhered to.23-01-20, 06:27 AM
-
Reply to NL Takata Airbag AlertDealers are not allowed to release a car that has an outstanding warranty recall. This is part of their franchise agreement.
However in this instance you can sign a waiver stating you understand the risks associated and confirm that MMAL...22-01-20, 05:09 PM -
If you read my post and who i quoted, we are talking MQ here Not MN.
On an MQ , all the steps I mentioned are required....22-01-20, 03:52 PM -
Reply to NL Takata Airbag AlertIts part of a document from MMAL regarding any recall. They are not allowed to release any vehicle that has an outstanding Recall. I believe in this instance though you can sign a waiver saying you have refused the offer of a buy back
Edit:...21-01-20, 07:44 PM -
There is nothing hard about doing them, its just the OTHER items that can cause issues. The injector washers must be changed, and the sealing area meticulously cleaned. The injector washer must be replaced and the injectors must be torqued with new...21-01-20, 04:40 PM
-
Reply to NL Takata Airbag AlertI agree. Dealers are told NOT to release cars back to the owner that are not fixable.
Are they allowed to do that??...21-01-20, 04:28 PM -
-
Reply to The End of an Era?More likely to be a rebadged Nissan Patrol If the "Alliance" have their way. The new mitsubishi L300 coming out this year is a Renault Trafic.
...
15-01-20, 06:22 AM -
Not sure why they quoted one for KR0W. It is RWD variant, not ADR compliant13-01-20, 09:22 AM
-
-
I thought All AU Pajero sport were KS1W. Unfamiliar with what the KR0W is?11-01-20, 04:01 PM
-
Reply to Gen 2 Pajero SportI had my first drive of one today. Exceed. Not very different to QE in that respect, instrument panel is cool, and steering wheel now has twice as many buttons on it.
New SDA (audio system) with volume knobs :-) instead of buttons...10-01-20, 08:16 PM -
-
Reply to Rear brake changeHandbrake on QE is on shoes inside the rotor. If you are just doing pads then no action needed. if you are doing rotors or they need machining you need to a deactivate handbrake and reset procedure.08-01-20, 04:06 PM
-
Reply to 7 months ownershipDISAGREE. DPF and EGR work well on MQ Triton. None of the problems associated with Pajero or ML Triton.
MQ was designed with EGR and DPF in mind, with the PAJ & ML its a bodged up system to drag an out of date design into the...29-12-19, 08:03 PM -
Reply to First Paj service coming upThey are ok to do catch can and fuel filter, but cant do anything that would negate the EGR.
Might as well use the CPS, you have paid for it already.29-12-19, 06:16 PM -
Reply to First Paj service coming upEGR delete strongly advised, these engines get a lot of carbon build up inside the inlet manifold. Along with a catch can, the most important things to do.
If using non dealer for service, ensure they use the right oil for your model,...29-12-19, 12:25 PM -
Reply to Fog lights wiringNot without a separate relay. You could blow your ETACS if you connected it directly28-12-19, 10:35 AM
-
-
Reply to Spare Wheel Liftercant make it out from the pics, but you have removed the half moon shaped cover at the top of the wheel havent you?26-12-19, 02:41 PM
-
Reply to headlight removalremove the front bumper bar. Its behind it. You can remove one side if you are careful and let it hang down, but its better to remove entirely26-12-19, 02:38 PM
-
Reply to OBD2 port powerThat power is a constant, when using a scantool you need a constant that isnt interrupted by cranking the engine. Of course you can put your own accessory there, but if a fault occurs you need to keep that in mind, and tell anybody that is doing diagnosis...26-12-19, 02:36 PM
-
Reply to DPF issues-2009 captivaYou would need a bi directional scantool, one that can send info as well as receive. To clean it you have to remove it and use a jet washer to reverse clean the soot out. There will be some restriction as you do this, this is normal, so you will need...24-12-19, 05:54 PM
-
Reply to Lowering Rear AirCon10mm socket short extension with wobble on the end or UJ and a ratchet.24-12-19, 08:36 AM
-
Reply to Removing the Intro Screen MessagePLEASE get the dealer to do it.
I had a MQ recently with a problem, customer had updated software from internet sourced software, and MMAL rejected replacing the unit as it could no longer take factory updates.
...22-12-19, 07:29 AM -
Next time it does it try shifting to N or even just wiggle gearlever. Inhibitor switches can give same symptoms.
Except it should start when hotwired....21-12-19, 09:45 AM -
-
Reply to Confirm my model?Its a GLX.
Does it still have the roof rack and genuine towbar on it?20-12-19, 03:20 PM -
Reply to Air Conditioner Fan FaultSound like the fan resistor may have a problem. They get dry solder joints, and banging the dash can alleviate the problem short term. Worth having a look at joints with a magnifying glass19-12-19, 08:35 PM
-
Reply to Pajero sport breaks on NS pajero???No the brakes an a Pajero sport are much smaller and calipers are different17-12-19, 08:35 PM
-
Reply to MUT 3 tool for SQILEngine is 85 Fuel should be 45. Was there an initialisation for fuel pump?
Also Barometric pressure should be 70kpa or more
The only times i have NEVER been able to get it done was when the car had been...17-12-19, 03:56 PM -
Reply to Noisy Aircon )5 NP ExceedNothing factory will be bolted in front of it. Might be an accessory item16-12-19, 08:12 PM
-
Reply to Boost control solenoidHow dirty is the inside of your inlet manifold?
If it is badly carboned then, because of the position of the sensor pick up, it will give low boost code16-12-19, 08:11 PM -
Reply to Noisy Aircon )5 NP Exceedpollen filter is behind the glovebox. Panel held on by 2 screws.16-12-19, 06:15 PM
-
Reply to MUT 3 tool for SQILDo you have the parameters right? Engine temp 85 Auto Trans 60 and fuel temp 45?
Also try initializing fuel pump in the INITIALISATION menu.
Snap On scantools will do the SQL but you need everything right. Also...16-12-19, 06:14 PM -
-
Reply to Radio codeMMCS will not need code
If bluetooth is locked then 0000 or 1212 can unlock normally14-12-19, 04:27 PM -
Reply to Help - buying MY14 NW ExceedWorth speaking to a Dealer about goodwill claim. If no luck, shop around other dealers nearby....11-12-19, 12:47 PM
-
Reply to Help - buying MY14 NW ExceedThe story goes that during engine assembly one member of the team wasnt wiping the block surface clean of anti corrosion treatment and when FIPG and the sump were installed the sealant never stuck to the block efficiently. When we remove the sump to...11-12-19, 12:20 PM
-
Reply to Help - buying MY14 NW ExceedFYI if build date is prior to 5/2/14 and its now out of warranty then a goodwill claim would be appropriate. After this date the "production process was improved" and shouldnt happen. But it still does :-s11-12-19, 11:06 AM
-
Reply to Help - buying MY14 NW ExceedProbably a 2-3 hour job. Poor adhesion of FIPG due to bad prep at engine assembly causes leak. Certainly a warranty job...11-12-19, 07:49 AM
-
Reply to Help - buying MY14 NW Exceedok, 4 tyres in 55k? Been driven hard i think.
Oil leak? Sump FIPG leaking. Leaks collect at rear of sump
Brake fluid needs changing
Excessive smoke under heavy load? Could be made worse bydirty...10-12-19, 06:52 PM -
FYI the sensors must be fitted in the correct orientation IE connectors must go horizontally in to sensor not vertically09-12-19, 03:55 PM
-
Reply to DPF burn intervalit is calculated by inputs from all the sensors, load, air temp, speed, water temp etc. if the targets are efficiently acheived it will do the burn as needed, and will lengthen the start distance, which is what you want.
If they are not...07-12-19, 04:14 PM -
Reply to DPF burn intervalI know all the other mitsi DPF start out at around 750 kms. If it is working well then it will climb to around 1000 ( the max i have seen, but workshop manual states 2500km), and if it is not working well it drops down.
I have seen problems with...05-12-19, 10:03 PM -
2016 triton is MQ and they are due at 45000 Its only MN that had the weird schedule.
I dont understand how a garage can tell if it is a tight tappet by listening to them. Your MQ inlet valves will be all tight I guarantee. And the...01-12-19, 10:09 AM -
Im not familiar with this torque app. Can it show fuel pressure? My first thought was a sticky suction control valve. Doesnt always give a fault code either.
You could always run it on neat injector cleaner. Block off the return...22-11-19, 07:02 PM -
Personally id be double checking the hoses first.18-11-19, 06:11 AM
-
Reply to Fuse slot 7 (driver’s side)My bad, Didnt read the ignition switched in OP.
Are both terminals inside the holder? I.E. feed terminal there but no consumer circuit17-11-19, 07:45 PM -
Reply to Fuse slot 7 (driver’s side)what model is it? It could be the "Transit fuse" or IOD as MM call it.17-11-19, 07:04 PM
-
Reply to Clicking from center/rear of car.Nice one :-)
. Dont get many of them doing that , but have seen it enough times to remember. i have heard of people wanting to change shafts and diffs because of that noise.
It is worth putting the cap back...17-11-19, 08:17 AM -
Reply to Clicking from center/rear of car.I have seen a few with rear driveshaft nuts loose, and some with rust in the splines causing knocking. If the nut is tight, loosen it and check if you can move shaft in and out. If not, WD40 the hell out of it till it does move freely , then retorque...15-11-19, 09:15 PM
-
Reply to Engine bay noiseHas it had its 30000 km service? If so it might be a leaky gasket on the egr valve that wasnt tightened enough during valve clearance adjustment . If they are not tight enough it screeches like a loose drivebelt.15-11-19, 05:17 PM
-
Here is a tip for when you refit the towbar.
Put an extra washer on the bolt nearest the left hand corner.All the bolts should have 1 washer, but a second washer on that particular bolt stops an annoying ratlle/clunk from towbar....14-11-19, 07:51 PM -
If you do have to remove rear a/c its no worry.
Just undo the 4 bolts and let it hang down.
Gives you plenty of room to get to towbar bolts14-11-19, 06:14 AM -
Reply to Spotilghts againThe range of the ultrasonics is minimal, about 1.5 metres. The sensors see nothing beyond that. The Blind spot warning sensors are a bit stronger. Rear
cross traffic alert uses different system, with Large Units behind the bumper bar. ...08-11-19, 06:36 AM -
Reply to Forgotten passcodeOk. If you press SETTINGS and MAP at the same time and hold them for 3.5 seconds, then the service screen will appear. From there you go to Hands Free Module, and on that page is an UNLOCK option..08-11-19, 06:08 AM
-
Reply to Spotilghts againIt uses the radar behind the badge. Yes i have tried it. the car doesnt brake for you, it pre pressurises the braking system ready for you to just touch the pedal. the pump makes a lot of noise when it happens.Very unnerving first time i tried it....07-11-19, 04:03 PM
-
Reply to Forgotten passcodeDo you have Settings button along the bottom of radio next to info button?...07-11-19, 03:59 PM
-
Reply to Spotilghts againThe radar sits behind the badge in the centre of the grille, so anything in its area can affect it.
You can turn off adaptive cruise control, but cant turn off Forward collision mitigation.07-11-19, 06:15 AM -
-
Reply to rocker cover oil sealsA few drops of superglue around the top injector seals is a good idea on Pajero. Not uncommon for them to work their way up the injector.31-10-19, 08:19 PM
-
Reply to Injector lifespanIn 6 years working for Metro Dealer I have only seen 3 or 4 MN or PB that have required injectors. I dont see it as a common problem.
The biggest unknown factor I believe is cause by Motors that have been Misfuelled (petrol)...30-10-19, 09:23 PM -
Reply to Service costs100%
NX Paj generally appear to be ok, they always need some adjusting, although they rarely are tight, but the MQ and MR Triton inlet valves are always tight at service, and the exhaust valves are slightly looser than spec....30-10-19, 06:54 PM -
Reply to Access through firewallyou can always use the accessory wires prefitted to the factory harness. There are three, factory towbar wiring uses 1, if you have trailer brakes you use another, so 1 is left. connector is 4 pin connector on inner guard (only has 3 wires) and the...26-10-19, 09:10 PM
-
Reply to Towpro triggers ACC and FCM WARNINGSThey work ok, but only engine and auto codes. I bought two last time they were on special, one for my tool box and one to keep in my trunk, just in case....26-10-19, 09:00 AM
-
Reply to Stiff steeringHigh trans oil is just as bad as being to low. Get them to fix asap25-10-19, 07:22 AM
-
Reply to SQL without MUTIIIThey will all do a SQL on their own as long as conditions are right. Pajero and MN Triton need to be at least 85 degrees engine temp, auto temp at least 60 degrees and fuel temp at 45 degrees. Then with steering wheel dead straight and no lights or...24-10-19, 07:11 PM
-
Tell them to refer to Hotline fix NX54-001. This details the update you are talking about....24-10-19, 07:03 AM
-
Reply to Catch Can DilemmaNo i have seen a couple of triton MQ with 250000. Same motor though. Highest QE is 120000, did second set of valve clearances on it last week.. Inlets slightly tight, exhausts slightly loose. No soot evident, although no manifolds have to come off its...18-10-19, 08:25 PM
-
It was the CH Lancer that got Takata Airbags refitted. They were brand new Items, and this was only a temporary measure. All the affected vehicle were re-recalled for a complete airbag and inflater replaced with another brand18-10-19, 05:53 PM
-
Reply to Catch Can DilemmaAs long as the catch can has been fitted correctly and in a sensible manner I cant see why any dealer would be bothered about it. The dealer I work for document the modifications made for history, but dont reject a claim just for the hell of it.
...18-10-19, 07:16 AM -
Reply to Key for doors onlyno problems at all with doing that. Even if you do try to start it by mistake it may log a code, but wont affect anything17-10-19, 05:02 PM
-
Insist on getting a genuine screen.......16-10-19, 07:21 PM
-
Reply to Brake fluidThe moisture in the brake fluid will boil under heavy braking, the pedal will sink to the floor and you will not stop till you hit something.16-10-19, 07:29 AM
-
Reply to Brake fluidEvery 30000 kms or two years is the schedule. Also if the moisture content is high16-10-19, 07:23 AM
-
Reply to NX towbarAll Pajero come with the straight bar fitted at factory, and gets junked when a towbar gets fitted....15-10-19, 07:04 AM
-
Reply to NX Alternator ProblemsDo you have a sensor on the battery negative cable near to the terminal?
This is the charge sensor. If you do have one, then any earths for accessories should NOT be connected directly to battery negative terminal, but to...11-10-19, 07:20 AM -
Reply to MJ 4d56tI honestly would steer clear. I don't believe they made one, unless you have a 2wd and want the low power 2wd model. The old ML diesel is a better unit....08-10-19, 09:00 PM
-
It is the lower control arm.
And if anyone is that bothered about the wait, ask for a loan car until its repaired...04-10-19, 09:23 PM -
-
-
Reply to Removing the Intro Screen MessageThere will be a software difference as the system will be on the CAN bus, and all the other systems on its sub net (CAN 1, CAN2 etc.) will need to know to expect data from the ACC...04-10-19, 08:14 AM
-
Reply to Idle too high-3.5l petrolTry holding the motor as a friend turns key on. You should feel it moving03-10-19, 03:50 PM
-
-
-
Once you reset the service indicator past the required time or distance the only way to set it to the correct interval is to use a scan tool to set an EXTRA REMINDER. Doesnt have to be A MUT3 though. I know the snapon and Launch scan tools can do t...30-09-19, 08:01 AM
Leave a comment: